[ Prob. 3] The voltage is = 20 sin ( 377t + 15 ) volts %3D and the current is = 4 sin ( 377t - 15 ) amperes. Determine the following: frequency, real power, reactive power, apparent power, power factor Then in a graph, sketch 1/4 of the waveforms both from min. to max. Specify the ff: phase of v & i; amplitude level/value of v & i ; location of max values in degrees, phase angle difference between voltage and current.

[ Prob. 3] The voltage is = 20 sin ( 377t + 15 ) volts %3D and the current is = 4 sin ( 377t - 15 ) amperes. Determine the following: frequency, real power, reactive power, apparent power, power factor Then in a graph, sketch 1/4 of the waveforms both from min. to max. Specify the ff: phase of v & i; amplitude level/value of v & i ; location of max values in degrees, phase angle difference between voltage and current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram and question. please answer it based on your knowledge. thank you so much!)
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
Exercise 11) Transform the circuit in phasor domain representation2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of voltage across resistor and capacitor5) Convert in rms values.
1. For the following sinusoids, determine which one leads and by how much a. ?(?) = 10cos (4? − 60°) and ?(?) = 6sin (4? + 50°)b. ?ଵ(?) = 4cos (377? + 10°) and ?ଶ(?) = −20cos(377?)c. ?(?) = 13 cos(2?) + 5 sin(2?) and ?(?) = 15cos (2? − 11.8°)
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel Add the following two impedances (a) in series and (b) in parallel. Z1 = 4 + 3i and Z2 = 12 + 5i
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage VR and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60Hz , R = 10 ohm Vcoil = 22.4 V. VR = 20 V and v = 36v , find the resistance and inductance of the coil.
Q5. For an exhibition project you are designing a circuit of signal processor which can be connected to 230V, 50 Hz supply have a 5.0 H inductor, 80 μ F capacitor and 40Ω resistor kept in series. How can you evaluate the rms current and average power delivered to the circuit? Based on your observation, evaluate the potential drop across capacitance and inductor. Comment about that r m s voltage found in this circuit is less than peak voltage? Justify it with your answer. If you remove the inductor and connect a bulb in series with a capacitor. What will happen to the brightness of bulb if it is connected to DC source and then to an AC source. Assess and find reason for your observations in each case.
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage V and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60 Hz, R = 10 R. Vcoil = 22.4 V, VR= 20 V and V = 36 V. find the resistance and inductance of the coil. please use reference photo
1. An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall power factor is to be unity (in resonance)? The circuit is energized by a 120 volt, 60 cps source. 2. The given figure is to be designed to pass a wave having a frequency of 3500 cps and block a 2500 cps wave. The series inductor has an inductance of 0.0023 henry. Calculate the capacitance of the series capacitor and the parallel inductor.
What is the equation of the current in B in the function of sin given that Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by π/3 radians and the total linecurrent is 23.4 amp. (rms).
Two sinusoidal voltages of the same frequency have rms values of 8 V and 3 V. What is the smallest rms value that the sum of these voltages could have? The largest? Justify your answers.