Problem 01.013 - Probability of fatigue failure - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS A fatigue test is performed on rotating beam specimens where, for each rotation cycle, the specimens experience tensile and compressive stresses of equal magnitude. The cycles-to-failure experience with 69 specimens of 5160H steel from 1.25-in hexagonal bar stock was as follows: x₁ 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 8 12 6 10 8 5 2 3 2 1 O 1 f 2 1 3 5 where x; is the life in thousands of cycles and fis the class frequency of failures. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Problem 01.013.b - Predicting fatigue failure Presuming the distribution is normal, how many specimens are predicted to fail at less than 115 kilocycles? Presuming the distribution is normal, specimens are predicted to fail at less than 115 kilocycles.

Problem 01.013 - Probability of fatigue failure - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS A fatigue test is performed on rotating beam specimens where, for each rotation cycle, the specimens experience tensile and compressive stresses of equal magnitude. The cycles-to-failure experience with 69 specimens of 5160H steel from 1.25-in hexagonal bar stock was as follows: x₁ 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 8 12 6 10 8 5 2 3 2 1 O 1 f 2 1 3 5 where x; is the life in thousands of cycles and fis the class frequency of failures. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Problem 01.013.b - Predicting fatigue failure Presuming the distribution is normal, how many specimens are predicted to fail at less than 115 kilocycles? Presuming the distribution is normal, specimens are predicted to fail at less than 115 kilocycles.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph. Answer: breaking stress,true stress at fracture and limit of proportionality.
Civil engineers often use the straight-line equation, = b 0 + b 1x, to model the relationship between the shear strength y of masonry joints and precompression stress, x. To test this theory, a series of stress tests were performed on solid bricks arranged in triplets and joined with mortar. The precompression stress was varied for each triplet and the ultimate shear load just before failure (called the shear strength) was recorded. The stress results for n = 7 resulted in a Coefficient of Determination of 0.8436. Given that r 2= 0.8436, give a practical interpretation of r 2, the coefficient of determination for the least squares model. a. We expect to predict the shear strength of a triplet test to within about 0.8436 tons of its true value. b. About 84.36% of the total variation in the sample of y-values can be explained by (or attributed to) the linear relationship between shear strength and precompression stress. c. In repeated sampling, approximately 84.36% of…
6. Discuss the different types of volume change in concrete at early and long-term ages. 8. A center-point loading flexural test was performed on a concrete beam having a size of100×100×500 mm. The beam is sitting on two supports located at 25 mm from each edge ofbeam. If the failure load was 17.5 kN, find the flexural strength.9. Considering the two tests of flexure, 3-points and 4-points, which one is more suitable forbending test and why?10. The compression strength test was performed on several samples of concrete molded in fourtypes of molds cubes of 0.100 m×0.100 m ×0.100 m and of 0.150 m×0.150 m × 0.150 m, andcylinders having a cross section of d=100 mm by H=200 mm and d=150 mm by H=300 mm,respectively. If the weight of the samples and the loads at failure are as given in the Table. Bothcubes and cylinder samples are cast from the same concrete batch under the same conditionsand subjected to the same curing method.11. Calculate the density (in kg/m3) and the compressive strength…
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mmdiameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) : a) Modulus of elasticityb) Yield strengthc) Toughnessd) Resiliencee) Shear modulusf) Bulk modulusg) Ductility as described bypercent change in length
A 316 steel plate sample is under the following loading condition:?(sigma) = 90 40 0 40 −50 0 0 0 0 MPaa. Plot the shear and normal stresses on a given oblique plane (rotated plane) on a graph (stress vs. angle) and show the max. shear plane and the principal planes.b. Draw the Mohr circle for the loading state above to scale (using a proper computer program or using a compass with correct scales on the axes) and show the angles you found in (a).c. If the steel sample has a Young’s modulus of 193 GPa, compute the dimensional changes of the plate under the above loading condition
A tensile test was conducted on a mild steel& the following data was obtained as follows. Diameter of the steel bar = 3 cm,Gauge length of the bar = 20 cm. Load at elastic limit = 250 kN . Extension at a load of 150kN = 0.21 mm . Maximum load = 380 kN . Total extension = 60 mm . Diameter of the rod at failure = 2. 25 cm Determine: (a) Young’s modulus (b) stress at elastic limit (c)the percentage of elongation (d) Percentage decrease in area.
A tensile test is conducted on a mild steel bar. The following data was obtained from the test : diameter of the steel bar= 3cm, Gauge Length of the bar = 20cm, Load at Elastic limit= 250kN, Extension at a load of 150kN= 0.21 mm, Maximum Load = 380kN, Total Extension= 60mm, Diameter of the rod at failure=2.25cm, determine young's modulus?
Read and Solve carefully please Write clearly and Box the Final answer Express your answer to 3 Significant figures and include appropriate units. QUESTION : Recall that for spings the Zimmerli point on the modified Goodman diagram is located at (Ssm, Ssa) = (55, 35) ksi. Suppose that a particular spring wire has a shear ultimate strength of Ssu = 89 ksi. Determine the shear endurance limit of the spring wire. Give your answer in units of ksi,
The following data were obtained from a standard tensile stress test on a mild steel specimen. Graph the result and determine proportional limit stress and Young’s Modulus.
? (sigma) = 90 40 0 40 −50 0 0 0 0 MPaa. Plot the shear and normal stresses on a given oblique plane (rotated plane) on a graph (stress vs. angle) and show the max. shear plane and the principal planes. (like in the image, using excel) b.If the steel sample has a Young’s modulus of 193 GPa, compute the dimensional changes of the plate under the above loading condition. Shear moduli is 70Gpa.
A mild steel bar went through a tensile test conducted at the University of San Carlos Mechanical Engineering Laboratory. The following data was obtained from the test: i. Diameter of the steel bar = 30 mm ii. Gauge length of the bar = 200 mm iii. Load at the elastic limit = 250 kN iv. Extension at a load of 150 kN = 0.21 mm v. Maximum load = 380 kN vi. Total extension = 60 mm vii. Diameter of the rod at the failure = 22.5 mm Determine the Young’s modulus, the stress at the elastic limit, the percentage elongation, and the percentage decrease in area.
A straight bar of uniform cross sectionis tested in tension. The bar's cross sectional is 6.5 square centimeters and a length of 4 m. When the tensile load reaches 85kN, the total elongation is 2.5mm. What is the stress and the modulus of elasticity of the bar?