PROBLEM 02: Water is flowing at a rate of 7 ft^3/s, and it is assumed that the head loss from the reservoir to the gage is equal to twice the velocity head in the 12-in pipe. p = 14.5 psi Elevation = 33ft 12" diameter Elevation = 20ft HL = 2- 2g 16" diameter water Elevation = 7ft

PROBLEM 02: Water is flowing at a rate of 7 ft^3/s, and it is assumed that the head loss from the reservoir to the gage is equal to twice the velocity head in the 12-in pipe. p = 14.5 psi Elevation = 33ft 12" diameter Elevation = 20ft HL = 2- 2g 16" diameter water Elevation = 7ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
For this siphon the elevations at A, B, C, and D are: 30 m, 32 m, 27 m, and 26 m, respectively. The head loss between the inlet and point B is three-quarters of the velocity head, and the head loss in the pipe itself between point B and the end of the pipe is one-quarter of the velocity head. For these conditions, what is the discharge and what is the pressure at point B? The pipe diameter 25 cm.
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
Pressures at the start and end of a straight horizontal pipe pumping water are measured as 2560337.6Pa and 168693.4Pa, respectively. Calculate the head loss due to friction. (Lemme Know If anything missed)
A 500 mm diameter pipe gradually reduces to 20 mm diameter and the gradually enlarge to its original size. Given the pressure at the base of the convergence of 0.60 MPa with a flow of 0.08 cu. m/s, 1. What is the velocity at point 1? 2. What is the velocity head at point 2? 3. Neglecting the head loss, the pressure of the smallest section is?
Aa certain hydro-power station has a head of 500m between the upper and lower reservior. A. Determing the approach velocity of water as it enters the turbine ; B. If the volume flowrate is 60cumec, what is the diameter of the penstock; and C. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity approach and the corrected diameter of the penstock required
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
Water at 20°C is pumped through a smooth 12-cm-diameter pipe 10 kmlong, at a flow rate of 75 m3/h. The inlet is fed by a pump at an absolute pressure of 4 MPa.The exit is at standard atmospheric pressure (101 kPa) and is 200 m higher. Calculate the frictional head loss Hf and compare it to the velocity head of the flow.
An oil of specific gravity 0.89 is flowing through a horizontal venturimeter fitted to a 242 mm diameter pipe at the rate of 108 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 841 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.13 N/mm2.
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION