Problem 1: (6 pts) The adjacent figure shows a circuit containing 4 resistances: (R₁-402, R₂-422, Ry-102 et R-15 22) connected to a power supply of voltage 32 V. Calculate: 1- The equivalent resistance of the circuit (Reg) 2- The total current (1₁) 3- The current and the voltage for each resistance 4- The energy dissipated by each resistance 5- The power delivered by the source U = 32 V R₁ - 400 D R₂-40 Ry=100 B C R-150

Problem 1: (6 pts) The adjacent figure shows a circuit containing 4 resistances: (R₁-402, R₂-422, Ry-102 et R-15 22) connected to a power supply of voltage 32 V. Calculate: 1- The equivalent resistance of the circuit (Reg) 2- The total current (1₁) 3- The current and the voltage for each resistance 4- The energy dissipated by each resistance 5- The power delivered by the source U = 32 V R₁ - 400 D R₂-40 Ry=100 B C R-150

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please show a complete step-by-step solution. Thank youGive your final answers in at least 2 decimal places - make it 3 or 4 decimal places whenever required in the problem. If you are doing a step by step calculation, maintain 6 decimal places in your in-between calculations to hit good accuracy in your final answers. Use 1 hp = 746 Watts in your conversion whenever necessary. A three-phase, 10-hp, 60-Hz, 1600-V, 500 r/min, salient-pole synchronous motor has direct-axis and quadrature-axis reactances equal to 37.10 Ohms/phase and 20.52 Ohms/phase, respectively. Neglecting losses, determine the developed torque if the field current is adjusted so that the excitation voltage is equal to 2.3 times the applied stator voltage, and the power angle is -18º. Give your final answer in 2 decimal places. Correct Answer: 921.26 ± 0.01
Please show a complete step-by-step solution. Thank youGive your final answers in at least 2 decimal places - make it 3 or 4 decimal places whenever required in the problem. If you are doing a step by step calculation, maintain 6 decimal places in your in-between calculations to hit good accuracy in your final answers. Use 1 hp = 746 Watts in your conversion whenever necessary. A three-phase, 30-hp, 60-Hz, 1900-V, 500 r/min, salient-pole synchronous motor has direct-axis and quadrature-axis reactances equal to 36.38 Ohms/phase and 24.25 Ohms/phase, respectively. Neglecting losses, determine the power, in watts, drawn by the motor if the field current is adjusted so that the excitation voltage is equal to 2.1 times the applied stator voltage, and the load is increased until maximum reluctance torque occurs. Give your final answer in 2 decimal places. Correct Answer: 172,167.36 ± 0.01
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • A 300V(line) 3-phase supply feeds a star-connected load consisting of non-inductive resistors of 15, 6 and 10Ω connected to the R, Y and B lines, respectively. The phase sequence is RYB. Calculate the voltage across each resistor.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • In a balanced three-phase wye-delta system, the source has an abc-phase sequence and Van=120<40° Vrms. The line and load impedance are 0.5+j0.4 Ω and 24+j18 Ω, respectively. Find the delta currents in the load.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • A Y-connected load is supplied from a 400V, 3 -phase, 3-wire symmetrical system RYB. The branch circuit impedances are ZR=10V3+j10; Zy=20+j20v3 ZB=0-j10 Determine the current in each branch. Phase sequence is RYB.
b) Explain Kirchhoff's law of meshes applied to solve the previous paragraph and how would you apply Kirchhoff's law of nodes? (no need to solve for Kirchhoff's law of nodes) d) Discuss the law of conservation of energy and verify it with your exercise data.
Lrocedure A- Kirchhoff's voltage law: The circuit in Figure 2 will be used o test the valdity of Kirchhoffs voltage law, Figure (2) Construct the circuit as shown in the figure (2). Measure the power supply output voltage and the potential drops across each of the thrae resistors. Record these measurements in your lab notebook as in the following table: University of Ti-Qar/ Departmnt of Elctricl aad Fectronlc Enginearing / Prepared by M 5¢ Al Karvem Soes 1+ Stage: Fundamentals of Flectrical Engineering | Lob 3 - Kirchhoff's Laws. 201520, Table 1; data collected for testing the validity of Kirchhot?s voltage law. 3)From your experimental data (table 2), calculate the total current into the node point P. Now calculate the total current out of the node point P along with its uncertainty. Does the current into the node agree with the current out of the node within experimental uncertainty?
Please show a complete step-by-step solution. Thank youGive your final answers in at least 2 decimal places - make it 3 or 4 decimal places whenever required in the problem. If you are doing a step by step calculation, maintain 6 decimal places in your in-between calculations to hit good accuracy in your final answers. Use 1 hp = 746 Watts in your conversion whenever necessary. A three-phase,50-Hz, 480-V system supplies the following loads:1. A six-pole, 50-Hz, 460-hp, three-phase, wye-connected induction motor, operating at 71 percent of the rated load with an efficiency of 93.6 percent and a power factor of 87.1 percent.2. A 55-kW, delta-connected, three-phase resistance heater.3. A 200-hp, 50-Hz, four-pole, wye-connected, cylindrical-rotor synchronous motor, operating at 51 percent of the rated load, with a torque angle of -13.2º.Neglecting copper losses, the synchronous motor is operating at 92.4 percent efficiency, and its synchronous reactance is 0.598 Ohm/phase. Determine the…
Identify the equation that proves Kirchhoff's Voltage Law for the circuit below given the following:ES1 = 8 V, ES2 = 14 V, R1 = 12 Ω, R2= 10 Ω, R3 = 22 Ω, and IT = 0.5 A
Use the reduce and return circuit analysis approach to solve for all voltages and currents in the circuit shown in figure 1 RT v1 v2 v3 v4 v5 IT I1 I2 I3 I4 I5 PE PR1 PR2 PR3 PR4
Subject:POWER SYSTEM ANALYSISAND DESIGNI want to know many details of these 4 Questions Answer. And the teacher who will do these questions and answers for me must explain part by part. If you send me the answers after five hours, there is no problem, but the handwriting must be clear. please do all the question, i need all the question please . Thank you in advance,
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • An abc-phase sequence three-phase balanced wye-connected source supplies power to a balanced delta-connected load. The impedance per phase in the load is 14+j12 Ω. If the source voltage for a phase is Van=120<80° Vms, and the line impedance is zero, find the phase currents in the wye-connected source.