Problem 1: A 10 ft. long simply supported laminated wooden beam consists of eight 1.5in. by 6 in. planks glued together to form a section 6 in. by 12 in. deep, as shown. The beam carries a 9 kip concentrated load at midspan. At section a-a, located 2.5 ft. from pin support A, determine: a) The horizontal shear stress in the glue joints at b, c, and d. b) The maximum horizontal shear stress in the cross section. 9 kips 2.5 ft a 5 ft B 5 ft 1.5 in. (typ) 12 in. Z 6 in. b с d

Problem 1: A 10 ft. long simply supported laminated wooden beam consists of eight 1.5in. by 6 in. planks glued together to form a section 6 in. by 12 in. deep, as shown. The beam carries a 9 kip concentrated load at midspan. At section a-a, located 2.5 ft. from pin support A, determine: a) The horizontal shear stress in the glue joints at b, c, and d. b) The maximum horizontal shear stress in the cross section. 9 kips 2.5 ft a 5 ft B 5 ft 1.5 in. (typ) 12 in. Z 6 in. b с d

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Each of the three rolled-steel beams shown (numbered 1, 2, and 3) is to carry a 64-kip load uniformly distributed over the beam. Each of these beams has a 12-ft span and is to be supported by the two 24-ft rolled-steel girders AC and BD. The allowable normal stress for the steel used is 22.5 ksi. Determine the section modulus for each girder and select the most economical W shape for the two girders using the table given below. (Round the final answer to one decimal place.)
Determine the shape of a fully stressed, simply supported beam that supportsa concentrated force at its center, Fig. 11–11a. The beam has a rectangularcross section of constant width b, and the allowable stress is sallow.
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown and w = 663.2 lb/ft. If the allowable strength of the glue in shear is 105 psi, Determine: (c) the maximum tension bending stress in the beam when the load of part (a) is applied. [σ = 1330 psi]
A 9 m beam simply supported at the ends carries a concentrated load of 10 kN at midspan. Select the lightest W section that can be employed using an allowable stress of 240 MPa. Determine the maximum stress of the selected beam.
A horizontal shelf AD of length L=1215mm, width b=305mm, and thickness t=22mm is supported by brackets B and C (Fig A). Note that the shelf is symmetric: AB=CD. The brackets are adjustable and may be placed in any desired positions between the ends of the shelf. A uniform load of intensity q, which includes the weight of the shelf itself, acts on the shelf. determine the maximum permissible value of the load q if the allowable bending stress in the self is = 8.5MPa and the position of the support is adjusted for maximum load-carrying capacity.
Can you provide me the step by step process of this? Thank you! A simply supported timber beam with length L = 6 m carries a uniformly distributed load w = 8 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 6-m span length.
A 4-m long simply supported beam has a section modulus of 1408 x 10³ mm³. The allowable stress in the beam is not to exceed 100MPa. The maximum distributed load that the beam can carry is most nearly,
The plate shown is made of UNS G10350 cold drawn steel (Sy=460 MPa and Su=550 MPa),and is fastened to an I beam made of UNS G10150 cold drawn steel (Sy=320 MPa and Su=385 MPa) by four rivets made of a steel with Sy=300 MPa and Su=365 MPa. Thickness of the plate is 10 mm and thickness of the flanges of the I beam is 15 mm. Diameter of the rivets is 20 mm. What safe load F (steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
A log that is 2 ft in diameter is to be cut into a rectangular section for use as a simply supported beam. If the allowable bending stress is sallow = 8 ksi, determine the largest load P that can be supported if the width of the beam is b = 8 in.
A symmetric I-section of size 180 mm × 40 mm, 8 mm thick is strengthened with 240 mm × 10 mm rectangular plate on top flange as shown is Fig. below. If permissible stress in the material is 150 N/mm^2, determine how much concentrated load the beam of this section can carry at centre of 4 m span. Given ends of beam are simply supported.
A cantilever beam is subjected to a concentrated load of 2000N. The cross sectional dimensions of the double-tee beam are shown. Determine (a) the shear stress at point H, which is 17 mm below the centroid of the double-tee shape, (b) the shear stress at point K, which is 5 mm above the centroid of the double tee shape, and (c) the maximum horisontal shear stress in the double tee shape.
A small balcony constructed of wood issupported by three identical cantilever beams (seefigure). Each beam has length L1 = 2.1m, width b,and height h = 4b/3. The dimensions of the balconyfloor are L1 XL2, where L2 = 2.5 m. The designload is 5.5 kPa acting over the entire floor area.(This load accounts for all loads except the weightsof the cantilever beams, which have a weight densityΥ = 5.5 kN/m3.) The allowable bending stress in thecantilevers is 15 MPa.Assuming that the middle cantilever supports50% of the load and each outer cantilever supports25% of the load, determine the required dimensions band h.