Problem 1 A ground profile consists of 2 m of silty sand underlain by 3 m of clay. The ground water table is 3 m below the ground surface. The sand has a unit weight of 14 kN/m3. The clay has unit weight of 16 kN/m3 above the water table and 20 kN/m3 below the water table. 1. Determine the total stress at bottom of the clay 2. Determine the pore water pressure at the bottom of the clay 3. Determine the effective stress at the bottom of the clay

Problem 1 A ground profile consists of 2 m of silty sand underlain by 3 m of clay. The ground water table is 3 m below the ground surface. The sand has a unit weight of 14 kN/m3. The clay has unit weight of 16 kN/m3 above the water table and 20 kN/m3 below the water table. 1. Determine the total stress at bottom of the clay 2. Determine the pore water pressure at the bottom of the clay 3. Determine the effective stress at the bottom of the clay

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.12P

See similar textbooks

Similar questions

A sediment settling lagoon has a depth of water of 4 m above the clay base. The clay layer is 3 m thick and this overlies 4 m of medium sand, which in turn overlies impermeable rock. Given the unit weight of clay, medium sand and sediment of silty fine sand is 18 kN/m², 20 kN/m³ and 16 kN/m², respectively. Calculate the effective stress at the top of the clay and at the top and bottom of the second layer under the following condition; i) initial, before any sediment is deposited. ii) After a 2m layer of sediment of silty fine sand has been deposited. iii) After draining the lagoon down to base level, with the same thickness (2m) of sediment still in place
A soil profile, under surcharge load of 25 kN/m2 at ground level, consists of 6m sand and 3m clay layer. Ground water table is 2m below sand layer. Dry unit weight and saturated unit weight of sand is 15.80kN/m3 and 16.90kN/m3 respectively. Clay layer, Gs=2.67 and saturated unit weight is 18.80 kN/m3. Determine a)Increase in stress at the mid layer of clay b) With dewatering 2m, what is the stress increase at the mid layer of clay c) How much must the water level be lowered to me more effective than the surcharged load?
A saturated clay layer has a thickness of 10 meters with a water content of 51% and a specific gravity 2.72. Determine the following: 1. Saturated unit weight of the clay * a. 21.46 kN/m³ b. 18.12 kN/m³ c. 16.87 kN/m³ d. 14.95 kN/m³ 2. total stress at depth of 10 meters a. 122.1 kPa b. 151.3 kPa c. 168.7 kPa d. 142.5 kPa 3. Effective stress at depth of 10 meters a. 42.1 kPa b. 70.6 kPa c. 68.7 kPa d. 82.5 kPa
A clay formation having a depth of 4 m. underlies a sand formation having a depth of 3 m. The dry unit weight of sand is 16.5 kN/m3 and the saturated unit weights of clay and sand are 20.4 kN/m3 and 19.6 kN/m3 respectively. The groundwater table is at the interface of the sand and clay. Compute the effective stress in kPa at the bottom of the clay if water rises 2 m. above the ground surface.
Problem # 4. A 2m. clay layer has values of e = 0.92, Gs = 2.72 and liquid limit of 40%. Above the clay is a 3m thick layer of sand with e =0.50 and Gs = 2.62. The water table is located 1.6 m below the ground. If a 3m thick backfill is placed on the ground surface having a unit weight of 17.3 kN/m^3, determine the following: a. Compression index of clay.b. Effective pressure at the midpoint of clay.c. Primary settlement for normally consolidated clay.
A 5-m depth of sand overlies a 6-m layer of clay, the water table being at the surface. The saturated unit weight of the sand is 19 kN/m3 and that of the clay is 20 kN/m3. Use the unit weight of water (?!) is 9.81 kN/m3. (a) Determine the total and effective vertical stresses at the centre of the clay layer. (b) The coefficient of lateral earth pressure at rest, ?", of the clay is identified as 0.8. Calculate the total and effective horizontal stresses at the centre of the clay layer.
A soil profile consists of; layer 1, 10m sand layer and layer 2, 3m clay layer. The ground water table is located 4m below ground surface. For sand, γdry=2.00 T/m2 (tons/m2), γsat=2.25 T/m2, and for clay layer, LL=46%, water content=42% and Gs=2.76. A uniform vertical stress, ΔP=20T/m2 is applied at the ground surface. Determine, a) Effective unit weight of clay, b) overburden pressure at the mid point of the clay layer, c) primary consolidation settlement
A dense silt layer has the following properties.void ratio = 0.30eff. Diameter ?10 = 10??capillary constant (c)=0.20 cm²Groundwater level is 8.0m below the ground surface 1. Calculate the height of capillary rise in the silt. 2. Calculate the vertical effective stress in kpa at 5m depth, assume ?? = 26.5 ??/?³and that the soil above the capillary action rise and ground surface is partially saturated at 50%. 3. Calculate the effective vertical stress at 10m depth assuming ?? = 26.5 ??/?³and that the soil above the capillary action rise and ground surface is partially saturated at 50%.
A 2m clay layer has values of e = 0.92 , Gs = 2.72 and liquid limit of 40%. Above the clay is a 3m thick layer sand with e = 0.50 and Gs = 2.62. The water table is located 1.6 m below the ground surface having a unit weight of 17.3 kN/cu. Meter, determine the following: a. Compression index of clayb. Effective pressure at the midpoint of clayc. Primary settlement for normally consolidated clay.......
A layer of saturated clay 4m thick is overlain by sand 5m deep, the water table being 3m below the surface. The saturated unit weights of the clay and sand are 19 and 20 kN/m^3, respectively; above the water table the (dry) unit weight of the sand is 17 kN/m^3 . Determine the effective stress at mid-height of the clay layer in kPa. Round your answer to 2 decimal places.
Determine the total stress of the dry sand with the dry unit weight, yd is 16.5 kN/m3 at the depth of 6 m.
A soil profile consists of two layers of soil with clay layer underlying the sand layer. The sand layer has a unit weight of 20 kN/m^3 having a thickness of 4 m. and the unit weight of the 2.5m layer of clay is 18 kN/m^3. Compression index of the clay is 0.22 with a void ratio of 1.30. Compute the effective stress (kPa) at the mid height of clay. Calculate the final settlement of the clay layer (mm) due to an increase of pressure of 30 kPa at the mid-height of the clay. Calculate the settlement (mm) when the water table rises to the ground surface.