Problem (1) A large vacuum tank, held at 60kmabsolute. Suck sea-level standard air through aConverging Nozzle whose throat diameter is (3 cm).Estimate @ the mass flow rate through the Nozzleand the Mach No. at the throat. Assume theflow as an isentrapic flaw.

Given Data The pressure inside the tank is: P2=60 kPa The nozzle throat diameter is: d=3 cm=0.03 m…

Problem (1): A large vacuum tank, held at sokf -absolute. Suck, sea-level standard air through a Converging Nozzle whose thront diameter is (3 cm). Estimate @ the mass flow rate through the Nozzle and the Mach No. at the throat. Assume the flow as an isentrapic flow.

Problem (1): A large vacuum tank, held at sokf -absolute. Suck, sea-level standard air through a Converging Nozzle whose thront diameter is (3 cm). Estimate @ the mass flow rate through the Nozzle and the Mach No. at the throat. Assume the flow as an isentrapic flow.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the acceleration of a 48.3lb block shown in the figure. Ans. a 2.8 ft per sec 48.3 lb swe…

Q: 2. In an irreversible process, there is a (a) loss of heat (b) gain of heat (c) no loss of work (d)…

A: As per the guidelines of BARTLEBY we are subjected to solve only three sub parts at a time. Please…

Q: Consider a Brayton cycle operating with a pressure ratio of 10. Air enters the compressor at 300 K…

A: Given that: Air enters the compressor at 300 K and the turbine at 1200 K Pressure ratio = 10 Case A:…

Q: for fuselage of an aircraft product How might you propose to fabricate this product? 5. Would the…

A: Given questions: For fuselage of an aircraft product How might you propose to fabricate this…

Q: are 3 methods that can be used to control the metal flow under the blank holder in deep drawing…

A: Drawing is a metalworking technique that involves stretching metal, glass, or plastic by applying…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2.…

Q: The modern engineering design and operation of fluid flow processes were developed using the…

A: Given question: 1. Explain the physical meaning of Bernoulli equation and list any assumptions to…

Q: A process innovated by Engr. Santioque is considered to be in a constant pressure. If there is ten…

Q: Three spur gears R,S and T are mounted on parallel shafts ,such that R meshes with S,and S meshes…

Q: B) In a metal forming operation, where the strength coefficient (K = 300 MPa), flow stress is 130…

Q: heavy truck is running up the track at an incline of 1 in 15 (sine) at a constant speed of 50 km/h.…

A: Solution.jpg

Q: Q/ Compute the tension (T) in the cable? Neglect the friction between .the cable and the pulley 44 C…

Q: C-A rigid 1 m³ tank contains nitrogen gas, initially at 10 bar, 27 °C. Heat transfer to the gas…

Q: = 0.95). A Q1: A vertical conduit is carrying oil (S.g differential mercury manometer is tapped into…

Q: Q.3 Select the word (advantages) or the word (disadvantages)) of the flowing expressions; (5 Pt.)…

Q: Below figure shows Ts diagram of an aircraft engine. Draw the engine diagram only. Answer the…

A: Given:

Q: With suitable sketch, explain the measuring instrument used for measuring the Gauge Pressure.

A: Gauge Pressure measuring Instrument: An instrument that is used for measuring the gauge pressure is…

Q: d= 1.50 in. t= 0.875 in. P= 7300 lb What is the average bearing stress produced in the support…

A: Given:- Diameter of pin (d) = 1.5 in Thickness (t) = 0.875 in Load (P) = 7300 lb To Find:- Average…

Q: Determine the resultant R of the two forces applied to the bracket. Write R in terms of unit vectors…

Q: A Brayton cycle with regeneration operates with a pressure ratio of 7. The minimum and maximum cycle…

Q: 2. The BSFC of a Formula1 car engine is 0.3 kg/kWhr and requires 1 kg of fuel every second. Its…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 30…

Q: Air flows over a flat plate at 45 m/s, 25°C and 1 atm pressure. a. What plate length should be used…

A: Given data: Fluid flowing : AirVelocity of flow = u = 45 m/sTemperature of air = 25°CAir pressure =…

Q: a) A gas is trapped in a piston-cylinder device. The initial pressure and temperature of the gas are…

Q: 1 d. The point A has coordinates (4, 1), AB = 9 5 BC Find the coordinates of B and the column vector…

Q: The 340-lb force is applied at point A of the bracket. Determine the moments of this force about…

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

Q: Which of the following statements is FALSE? A. O Employees who use portable vibrating equipment such…

A: Here two separate questions has been asked. As per honor code and answering guidelines I can answer…

Q: Q3:/ A large reservoir at (600 k) supplies air flow through a converging-diverging duct with throat…

Q: B=56 inside diameter = 66 in. wall thickness=0.23 in. allowable normal stress perpendicular to the…

Q: As shown in Figure A2-a, a piston-cylinder assembly with two set of stops contains a mass of 3 kg of…

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

Q: Thickness of the plate is reduced from 40mm to 20mm by succesive cold rolling passes using identical…

Q: 1. Find: Vs, we/c, and wa/A Use relative motion analysis OR Instantaneous center of rotation Given:…

Q: Water is pumped through a 500 mm diameter circular pipe which is 800 meters long at the velocity of…

A: Given data Diameter of pipe = d = 500 mm = 0.5 mLength of pipe = l = 800 mVelocity of flow = v = 2…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross- sectional…

Q: connects two pullets A and B the centres of which are 4 m a part. The belt has a mass of 1.15kg/m.…

Q: Handwritten and the unit should be in metric system. Three kilograms of water at 35 degrees Celsius…

Q: If moist air has a saturation humidity ratio of 0.016872 kg v/kg da at a pressure of 1.2 bar, what…

Q: Example 3.11. Fig. 3.18 shows a crank-lever ABC with a tension spring (7). The lever weighs 0.2…

A: Weight of the lever, W=0.2 N/mmLength of lever AB, LAB=200 mmLength of lever BC, LBC=100 mmLoad at…

Q: 378 kg/s of steam flows through a reaction turbine stage. The nozzle angle (8) is 18º. Fixed and…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A: Given data: F1=20 kNF2=20 kNF3=10 kNF4=50 kNM=145 kN.m Need to determine the equation of line of…

Q: A person is donating blood. The 0.36 L bag in which the blood is collected is initially flat and is…

A: Given: The volume of the blood bag, V = 0.36 L = 0.00036 m^3 The diameter of the tube, d2 = 2.8 mm =…

Q: completely balanced

A: Plane mass(kg) radius(m) centri force÷ω2 (kg.m) length(n) couple÷ω2 (kg.m2) A mA .18 .18mA -y…

Q: Air initially at 101.325 kPa, 30°C db and 40% relative humidity undergoes an adiabatic saturation…

A: The increase in the water content of the moist air is m.water = 0.246 kg/s.

Q: (a) Using the network reduction approach determine the system failure probability for the system…

A: Given:qA=0.02qB=qC=qD=qE=0.01qF=qG=0.015qH=qI=qJ=0.025

Q: 9) In hydrostatic extrusion, the billet is smaller than the chamber is used, Why? 10) Earing is a…

A: Question - 9: During extrusion process, the billet is inserted into the extrusion chamber where…

Q: Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick…

Q: Q1- if the 5 kg block is suspended from the pulley B and the sag of the cord is d=0.15m determine…

Q: b) Parallel-connected four centrifugal pumps each have a specific speed of 28 and operate at 1400…

Question

Problem (1) A large vacuum tank, held at 60km
absolute. Suck sea-level standard air through a
Converging Nozzle whose throat diameter is (3 cm).
Estimate @ the mass flow rate through the Nozzle
and the Mach No. at the throat. Assume the
flow as an isentrapic flaw.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compressible laminar fl ow, f≈ 64/Re, may occur in capillarytubes. Consider air, at stagnation conditions of 100°Cand 200 kPa, entering a tube 3 cm long and 0.1 mm indiameter. If the receiver pressure is near-vacuum, estimate(a) the average Reynolds number, (b) the Mach number atthe entrance, and (c) the mass flow in kg/h.
A large tank, at 500 K and 200 kPa, supplies isentropicairfl ow to a nozzle. At section 1, the pressure is only 120kPa. What is the Mach number at this section?(a) 0.63, (b) 0.78, (c) 0.89, (d ) 1.00, (e) 1.83 assume one-dimensional fl ow of ideal air, R 5287 J/(kg ? K) and k 5 1.4.
Air, at stagnation conditions of 450 K and 250 kPa, fl owsthrough a nozzle. At section 1, where the area is 15 cm2,there is a normal shock wave. If the mass fl ow is 0.4 kg/s,estimate (a) the Mach number and (b) the stagnation pressurejust downstream of the shock.
1. Air, with stagnation conditions of 800 kPa and 100 °C, ex pands isentropically to a section of a duct where A₁ = 20 cm² and p₁ = 47 kPa. Compute ( a ) Ma₁ , ( b ) the throat area , and ( c ) m . At section 2 between the throat and section 1, the area is 9 cm². (d) Estimate the Mach number at sec tion 2. Plz sketch and solve it
A gas, assumed ideal, flows isentropically from point 1,where the velocity is negligible, the pressure is 200 kPa,and the temperature is 300°C, to point 2, where the pressureis 40 kPa. What is the Mach number Ma2 if the gas is(a) air, (b) argon, or (c) CH4? (d ) Can you tell, withoutcalculating, which gas will be the coldest at point 2?
he reservoir pressure and temperature for a Laval nozzle are 5 atm [abs] and 520 K,respectively. The flow is isentropically expanded to supersonic speed at the nozzle exitwith area Ae = 4in2. If the exit-to-throat area ratio is 2.295, calculate the followingexit properties: g) ̇mass flow rate gamma = 1.4, R = 287 J/kgK Please show all work
Air, assumed to be a perfect gas from Table A.4, fl owsthrough a long, 2-cm-diameter insulated tube. At section 1,the pressure is 1.1 MPa and the temperature is 345 K. Atsection 2, 67 meters further downstream, the density is1.34 kg/m 3 , the temperature 298 K, and the Mach numberis 0.90. For one-dimensional fl ow, calculate ( a ) the massfl ow; ( b ) p 2 ; (c) V 2 ; and ( d ) the change in entropy between1 and 2. ( e ) How do you explain the entropy change?
A converging-diverging nozzle has a throat area of 10 cm2and an exit area of 28.96 cm2. A normal shock stands in theexit when the back pressure is sea-level standard. If theupstream tank temperature is 400 K, estimate (a) the tankpressure and (b) the mass fl ow.
An air tank of volume 1.5 m3 is initially at 800 kPa and20 °C. At t = 0, it begins exhausting through a convergingnozzle to sea-level conditions. The throat area is 0.75 cm2.Estimate (a) the initial mass flow in kg/s, (b) the timerequired to blow down to 500 kPa, and (c) the time atwhich the nozzle ceases being choked.
Consider the Gulfstream IV flying at Mach = 0.8 at an altitude with atmospheric pressure of 33,283.40-Pa. Calculate thrust required assuming a weight of 73,000-lb. Airplane data: S = 950 ft2, AR = 5.92, ?Do = 0.015, and K = 0.08. The thrust required. (in lbf)
Air at 800 kPa and 1200 K enters a converging nozzle with negligible velocity (i.e., these are stagnation or total values). The throat area of the nozzle is 10 cm?. Calculate and plot the exit pressure, exit velocity, and mass flow rate versus back pressure (exit pressures) from 100 kPa to 800 kPa by 100 kPa.
When operating at design conditions (smooth exit to sealevelpressure), a rocket engine has a thrust of 1 million lbf.The chamber pressure and temperature are 600 lbf/in2absolute and 40008R, respectively. The exhaust gasesapproximate k = 1.38 with a molecular weight of 26. Estimate(a) the exit Mach number and (b) the throat diameter.