For the assembly shown, determine the displacement of points B and D as the load of 50KN is applied at D. Rod BC is steel with length = 2m, A = 600mm2 E =200GPa.Bar ABD is rigid. What is the stress in the rod CB? What is the shear stress of the bolt of the pin at A if its diameter is 20mm? Please provide complete FBD. PROBLEM 1For the assembly shown, determine the displacement of point B and D as theload of 50KN is applied at D. Rod BC is steel with length = 2m, A = 600mm2 E =200GP..Bar ABD is rigid. What is the stress in the rod CB? What is the shear stress of the boltof the pin at A if it's diameter is 20mm?B imDetail of the pin at A

Answered: Image /qna-images/answer/0bdb662c-9566-40d6-a9a3-e4bfede7cfd2.jpg

PROBLEM 1 For the assembly shown, determine the displacement of point B and D as the load of 50KN is applied at D. Rod BC is steel with length = 2m, A = 600mm2 E =200GP.. Bar ABD is rigid. What is the stress in the rod CB? What is the shear stress of the bolt of the pin at A if it's diameter is 20mm? B Im Detail of the pin at A

PROBLEM 1 For the assembly shown, determine the displacement of point B and D as the load of 50KN is applied at D. Rod BC is steel with length = 2m, A = 600mm2 E =200GP.. Bar ABD is rigid. What is the stress in the rod CB? What is the shear stress of the bolt of the pin at A if it's diameter is 20mm? B Im Detail of the pin at A

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.3P

See similar textbooks

Similar questions

Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm). E = 200 GPa
Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. What is the corresponding displacement at B in millimeter if P = 57 kN and Q = 397 kN?
Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi.
A loading condition is shown below. The wires AB and CD both have yield strength (Sy) of 71 ksi, diameter of 1/4 in, and b = 2 in. a) Using either maximum shear stress theory or distortion energy theory, determine the maximum load P that can be applied before yielding happen in the wires. b) Using Castigliano's theorem, determine the horizontal displacement of point D.
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a Determine the displacement of point C caused by the 15-kN load. Use E = 200 GPa for steel.
The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF, and a rigid bar G. If the horizontal displacement of end F of rod EF is 0.45 mm, determine thethe magnitude of P.
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please
Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm).
A motor delivers 500hp to the tubular shaft, which has an outer diameter of 2 in. The shaft is rotating at 150 rad/s. 1 hp = 550 ft⋅lb/s. A) Determine its largest inner diameter if the allowable shear stress for the material is τallow= 25 ksi.
The drive shaft AB of an automobile is to be designed as a thin-walled tube. The engine delivers 150 hp when the shaft is turning at 1000 rev>min. Determine the minimum thickness of the shaft’s wall if the shaft’s outerdiameter is 2.5 in. The material has allowable shear stress of tallow = 7 ksi.
The rod is pinned at its end A and attached to a torsional spring having a stiffness k, which measures the torque per radian of rotation of the spring. If a force P is always applied perpendicular to the end of the rod, determine the displacement of the force. EI is constant.