Problem 1: Given the 2D states of plane stress below, determine the principal stresses (0₁, 0₂) and the maximum shear stress (Tmax). Show your work. Ox ºy Txy 90 MPa -30 MPa 15 MPa 90 MPa 180 MPa 60 MPa 0 MPa -40 MPa 120 MPa 01 02 03 Tmax
Q: The 5-lb box sides on the surface for which -0.3. The box has a velocity - 15 ft/s when it is 2 ft…
A:
Q: Derive the following expression of effects of partial balancing in two cylinder locomotive engine…
A: For two cylinder locomotive engine are balanced by placing the crank at 90 degree difference with…
Q: A particle moving along a straight line is subjected to a deceleration a=-4v m/s2, where v is in…
A:
Q: Find the amount (mass) in kg of ice produced in 8 hrs.
A: Given:Refrigerant=R134aEvaporator pressure, Pe=1000 kPaCondenser pressure, Pc=3 MPaMass flow rate of…
Q: 6. A force is applied to a particle over the 0.3 s time interval as shown below. The particle is…
A:
Q: Pleass explain step by step every detail and help me solve. We should do a free body diagram for…
A: Let the support A has two components Ax and Ay and the support E has roller supports . Thus, E has…
Q: 2. A suitcase slides down a ramp between Points A and B as shown below. It has an initial velocity…
A: (a) Write the given data. vi=2 m/sm=2.1 kgμs=0.3μk=0.2
Q: The four-wheel drive all-terrain vehicle (ATV) has a mass of 300 kg with center of mass G2. The…
A: Given Mass of the bike m2=300 kg Mass of the man m1=92 kg Coeffcient of friction μ=0.43
Q: Q3/A combustion chamber consists of tubular combustors of 15-cm diameter. Compressed air enters the…
A: Given, P1 = 480 kPa T1 = 550K V1=80 m/s Air-Fuel ratio = 40 Heat flow rate = 42,000 kJ/kg From…
Q: For the system shown a step torque is applied at 0₁(t). Given J and k1Nm. Find: = rad 1. The…
A:
Q: A simple Rankine cycle works between the boiler pressure of 5 MPa and condenser pressure of 5 kPa.…
A:
Q: 7.36 A long, cylindrical, electrical heating element of diameter D = 12 mm, thermal conductivity k =…
A: The diameter of the cylinder is D=12 mm=0.012 m. The thermal conductivity of the cylinder is k=240…
Q: A piston-cylinder device contains 5 kg of steam at 100°C with a quality of 50 percent. This steam…
A:
Q: A 30 lb block is subjected to a force, F = 60 lb as shown below. The block starts from rest. When…
A: Given: Mass = 30 lb F = 60 lb To find: Vertical datum Work done by block Work done by force
Q: Plot the dew point, specific volume and RH of moist air at a drybulb temperature of 16 deg C and a…
A: Given Data: A dry bulb temperature [DBT] =16 deg C and a moisture content of 0.00734kg moisture per…
Q: In the above solution the run of AC is taken to be 3in. I think this is incorrect since B and D are…
A: From the geometry : Take perpendicular from point C on the line AB. Let it intersect at point C' on…
Q: In the Great Lakes areas of the US, during the cold season, a freezing rain sometimes occurs, during…
A: Write the given data. Plate length, L=1.7 mFor air,p=1 atmT∞=265 KTs=275 KV=70 m/s
Q: Which of the following is a standard test for friction? O a. capstan test b.sled test c. inclined…
A: This question is from basic mechanics problem. We can answer this question by basic understanding…
Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…
A:
Q: 17-103 Air enters a rectangular duct at T₁ = 300 K, P₁ = 420 kPa, and Ma, = 2. Heat is transferred…
A: The given information in the problem is shown in the following attached image:
Q: In an SI engine working on the ideal Otto cycle the compression ratio is 6. The pressure and the…
A: Given:Compression ratio, r=6Pressure and temperature at the beginning of compression, P1=1.013 bar,…
Q: A 340 L tank contains steam, initially at 400°C, 3 bar. A valve is opened for 20 seconds and steam…
A: Given data:- Volume of tank =340 L Temperature =400 °C Pressure =3 bar A valve is opened for= 20…
Q: P2: explanation of how the microstructures of processed metallic materials affects the mechanical…
A: To explain: How the microstructures of processed metallic materials affects the mechanical…
Q: 2. The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…
A:
Q: Why cos(60 if I don't see that angle in the figure
A: This question can be solved by labelling angles.
Q: A 8-cm-diameter vertical water jet is injected upward by a nozzle at a speed of 15 m/s. Determine…
A: d=8cm and u=15m/s h= 2m ρ=1000kg/m3 We need to find Maximum weight of a flat plate that can be…
Q: 14-86. The spring is unstretched when s=1 m and the 15 kg block is released from rest at this…
A: Mass of block m = 15 kg Spring is unstretched when s=1 m K = 75 N/m θ = 30o To find out :-…
Q: QAI=?" 5MPa,370°C e = 60% WHPT =? (ACTUAL)MW e=G58 2 REQUIRED! 2 MPa Q R = Q² + ₂0 = MCN CAT QR -…
A: "Inlet condition turbine 1"T[1] = 370[C]P[1] = 5000[kPa] P[2] = 2000[kPa] "Reheat pressure" T[3] =…
Q: 3) Link AB of a robotic arm is rotating at a constant speed of 4 rad/s, while link BC is rotating at…
A:
Q: rovide a design outlining the ideal refrigerant and operating parameters for a direct contact heat…
A: The evaporator temperature is Te=-40°C. The condensing temperature is Tc=65°C. The isentropic…
Q: From the Animated Figure 8.25 compute the length of time required for the average grain diameter to…
A: To find: The time required. Given: The graph is shown below.
Q: which type of furnace is used for installation in a crawl space?
A: To explain: The type of furnace is used for installation in a crawl space. Concept used: Crawl…
Q: What is the percent voltage unbalance for a three-phase supply voltage of 485 V, 460 V, and 435 V
A: Given V1=485 VV2=460 VV3=435 V
Q: F 15° 0.6 m 1 m The crate has a mass of 58 kg and rests on the inclined platform of the truck.…
A: Given:- Mass of crate, m = 58 kg Coefficient of static friction, μs=0.7 Angle, θ=15° Gravity, g=9.81…
Q: L.Define the term alloy and give an example. 2.Why aluminium is useful for building aeroplane wings?…
A: These questions are based on the concept of material science. As per the guidelines we are…
Q: Consider a refrigeration system that operates on an actual vapor-compression refrigeration cycle…
A: Given:Refrigerant=R134aIsentropic efficiency of a compressor, ηisen=75.1%Refrigerant inlet condition…
Q: One slip system for the HCP crystal structure is {0001} . Sketch this plane along with the HCP atoms…
A:
Q: short cylindrical cast iron post supports a compressive load of 20 tons (40 kips). If the factor of…
A: This question is based on the concept of strength of material.
Q: A 0.3-m³ rigid tank is filled with saturated liquid water at 370°C. A valve at the bottom of the…
A:
Q: 1. Question 1- Laplace Equation: Leibmann's Method The four sides of a square plate of side 12cm,…
A:
Q: Problem 3. S-plane maps For each pair of 2nd order system specifications draw the s-plane map: (a)…
A:
Q: A 340 L tank contains steam, initially at 400°C, 3 bar. A valve is opened for 20 seconds and steam…
A: GivenV=340L=0.340 m3T1=400oCP1=3 bart=20sm˙o=-0.005 kg/s
Q: What safety precautions should be taken during welding and cutting operations?
A: Welding and cutting operations can be extremely hazardous if proper safety precautions are not…
Q: Make an orthographic projection.
A: The orthographic views for the given isometric object are drawn below with the actual scale 1:1
Q: An insulated room is heated by burning candles. Is this a heat or work interaction? Take the entire…
A: “Since you have posted a multiple question, we will provide the solution only to the first question…
Q: what is the answer of Ra
A: Given data:- To find:- Value of reaction Ra
Q: If there are two cannons, both completely identical and were shot at same speed and angle. One is…
A: Solution: Given Data: h2,max=114h1θ1=θ2v1=v2 To Find: The time of flight of cannon 2 in terms of…
Q: ! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…
A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…
Q: A 180-lb man and a 120-lb woman stand side by side at the same end of a 300-lb boat, ready to dive,…
A: The mass of the man is mm=180 lb The mass of woman is mw=120 lb. The mass of boat is mb=300 lb. The…
Q: 14-4. The 100-kg crate is subjected to the forces shown. If it is originally at rest, determine the…
A: Given data:- mass of object (m) =100 kg speed of object (v) = 8 m/s. The coefficient of kinetic…
Step by step
Solved in 3 steps with 3 images
- The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. aAt a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
- An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
- An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??..4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
- The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?