Problem 1: (P9, P10, M5, M7, D5) Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1-2880 N and T2-432 N. The maximum bending moment is at x = 230 mm (point B), and it equals M = 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). 230 mm | T, 280 mm 30-mm dia. 300 mm 250-mm dia.

Problem 1: (P9, P10, M5, M7, D5) Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1-2880 N and T2-432 N. The maximum bending moment is at x = 230 mm (point B), and it equals M = 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). 230 mm | T, 280 mm 30-mm dia. 300 mm 250-mm dia.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
Repeat Problem 6.2-17 but now use a transformed-section approach.
Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T0 = 10 kN.m is applied at point D. B) What is the maximum angle of twist, max and where does it occur?
Find the diameter of a shaft to transmit twisting moments varying from 800 N-m to 1600 N-m. The ultimate tensile strength for the material is 600 MPa and yield stress is 450 MPa. Assume the stress concentration factor = 1.2, surface finish factor = 0.8 and size factor = 0.85.
Design of a Shaft subjected to Alternating Loads 1. [Proof of Concept] Considéra machined steel circular shaft subjected to maximum and minimum bending moment of 1000 and 4000 lb .in, respectively; and a maximum and minimum torque of 250 and 1600 Ib.in, respectively. Consider the factor of safety to be 2, the yield strength of the materials 40 ksi, and its ultimate strength to be 70ksi.Determine the minimum diameter of the shaft for the case where D is 20% larger than d, the fillet radius is 10% of d, and reliability is 99%. You may use DE-ASM E formula. 2. Write a computer code that can take Tm, Ta, Mm, Ma, choice of material, safety factor, and other necessary assumptions from the user and return an estimated diameter for the shaft.Choice of inputs is up to you. Note that many of the required quantities are themselves function of the shaft diameter. Your code should be submitted with a report.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
Q.2 A hollow simple supported shaft 3m made of steel with di/do of 0.6. The shaft is subjected to a bending force of 4 KN and transmits 52 KW with 150 rpm. Find the outer and inner diameter of the shaft, if the ultimate shear stress of 600 MPa and allowable compression stress of 100 MPa, tack safety factor 7.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)