PROBLEM 1: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses. * Your answer

PROBLEM 1: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses. * Your answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 200 mmФ pipeline whose length and friction factor (f) are 2.5 km and 0.018 respectively connects two tanks A and B. Assuming minor loss to be 10% of friction loss, and reservoir A 15 m higher than B, find the rate of flow * a. 0.03426 m³/s b. 0.05426 m³/s c. 0.04426 m³/s d. 0.06426 m³/s
The middle 200m of a 600m long HDPE pipe (e=0.00015) with a diameter of 0.75m was damagedin a recent earthquake. Due to supply shortages, the middle 200m of pipe was replaced with a HDPEpipe 0.5m in diameter. If the entire pipe is required to carry 2m 3 /s of water (20°C), determine the totalhead loss across the entire 600m long pipeline. Ignore minor losses.
A circular pipe with a diameter of 13” carries water at an unknown velocity. The Reynold’s number for this flow is 2.0 x 106. What is the water’s velocity?
What is the expected head loss per 1 mile in feet of a closedcircular pipe (17 inches inside diameter), friction factor of0.03 when 3300 gal/min of water flow under pressure?
Write legibly Complex Pipeline System_Parallel Pipes 1. The pressure heads at junctions A and E are 70.0 m and 46.0 m, respectively, in the given parallelpipe system shown in the figure. Theflow rate of water entering junction A is 0.30 cms. Assuming that the Hazen – Williams roughness coefficient C = 120 for all pipes, determine the flow rate through each branch of the loop. For the solution, use the Hazen – Williams formula. Answer: a. Pipe ABE = _______________________ cmsb. Pipe ACE = _______________________ cmsc. Pipe ADE = _______________________ cms
A flow of 12.0 mgd is required through old cast iron pipe (C = 100) with a slope of the hydraulic grade line of 1.0 ft/1000 ft. Theoretically, how many 16′′ pipes would be required? 20′′ pipes? 24′′ pipes? 36′′ pipes?
Oil is conveyed on a 6” diameter pipe, sg=0.8 the velocity is 30ft/s. The pipe diameter narrows to 2”, a)what is the flow rate? b) how many times velocity is faster at the 2” diameter compared to the larger pipe? c)How much time would it take to fill 100ft^3?
A 600mm pipeline, 1550m long is to take water from a reservoir at elevation 150m and discharge it through a 150mm nozzleat elevation 25m. The pipeline is to be constructed so that at a point X, 200m from the nozzle, the pipe shall be 3m below the hydraulic gradeline. What would be the elevation of the pipe at X and what horsepowerwill be available in the jet from the nozzle? Assume f = 0.023 and no loss at entrance to pipe. Use device coefficient = 0.95. Please use figure when solving.
Diagram of the problem, necessary formulas, clearance and numerical solution What cross section must a pipe have if 0.065 m3/s of water passes through it, moving with a speed of 1.53 m/s? What should be its diameter?
A new cast iron pipe must carry 5.942 m3/s at a head loss of 18 m per 16 km length of pipe. Compute the diameter of the pipe in m using Hazen Williams Formula with C=179. Round your answer to 3 decimal places.
The elbow flow passage volume is 0.37 m3 between sections 1 and 2. The flow rate is 0.90 m3/s and the elbow inlet and outlet pressures are 200 kPa and 130 kPa. Consider the elbow weight is negligible. Calculate the horizontal and vertical anchoring forces to hold the elbow in place. my results were Frx = 132.8kPa Fry = 76.7kPa
13. Situation 5 - A 0.60 m diameter pipeline 30 m long carries 0.4 m^3/s of water. a. Compute the head loss, in meters, if n = 0.014. Round off to three decimal places. b. Compute the head loss, in meters, if f = 0.014. Round off to three decimal places. c. Compute the head loss, in meters, if C = 140. Round off to three decimal places.