Problem 1. The floor framing in the figure is loaded by dead loads, DL = 30 psf, and live loads. LL = 50 psf. Neglect the own weights of beams and girders. 1. Draw the load flow diagrams for column B-2 showing the propagation of loads through the various structural elements 2. Draw all necessary FBDs and calculate the column load for B-2 3@6¹ E 2@8¹=16¹ B1 اله G2 1 81 E G3 12¹ a. 00 IN G4 BIL 1.. GS1

Problem 1. The floor framing in the figure is loaded by dead loads, DL = 30 psf, and live loads. LL = 50 psf. Neglect the own weights of beams and girders. 1. Draw the load flow diagrams for column B-2 showing the propagation of loads through the various structural elements 2. Draw all necessary FBDs and calculate the column load for B-2 3@6¹ E 2@8¹=16¹ B1 اله G2 1 81 E G3 12¹ a. 00 IN G4 BIL 1.. GS1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a monotlithic floor framing plan, the columns are 300mm square, girders are 250mm wide by 450mm deep and slabs are 100mm thick. the floor loads include floor finish of 0.77kPa, ceiling system of 0.25 kPa, partition load of 1.0kPa and liveload of 4.8kPa. bar centroid from the edge of the beam is 70mm. calculate the ff: 1. total factored floor load in kPa 2. total factored uniform load on girder GH in kN/m 3. maximum ultimate bending moment at discontinuous end of girder GH in kN.m
Design a balcony slab of a residential house exposed to the weather. Observe how the moment diagram ofthe balcony is “scared-cat shape through-and-through”. The cantilevered span is 8 ft long and the servicelive load from residential house. Snow load is S = 30 lbf/ft2 and self-weight of the slab must be dead loadD. Apply Load Combinations 2, 3, and 4 only. Use steel reinforcement no greater than #6 size bars, andno smaller than #3; f’c = 4,000 lbf/in2; fy = 60,000 lbf/in2. Density of the concrete isdc = 100 lbf/ft3.Sketch the design.
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
The 10 ft rectangular wooden column hasthe dimensions indicated. Determine the critical load ifIt assumes that the ends are connected by pins.Ew = 1.6(103) ksi, sY = 5 ksi.
Q1- the reinforced flat plate roof slab system that shownin figure. Supports a service live load of 1.5 kN / m2 and a service superimposed dead load of 3.4 kN / m? in addition to its own weight. The slab is supported along its outer edges by a brick wall. Slab thickness is 200mm and wall thickness is 240mm. all interior columns are 300x600 mm. Using the ACI direct design method, design and detail the column strip top bars required at the continuous edges of strip A shown in the plan. Use fe-22 MPa andf-400MP.
2.2 A monolithic floor framing plan is shown in the figure. The columns are 300 mm square, girders are 250mm wide by 450 mm deep and slabs are 100 mm thick. The floor loads include floor finish of 0.77 kPa, ceiling system of 0.25 kPa, partition load of 1.0 kPa and live load of 4.8 kPa. Bar centroid from the edge of the beam is 70mm. Calculate: Total factored uniform load on girder GH in 2 decimal places, ____?____ kN/m
Q#3. An aluminium strut 14 ft long has a rectangular cross section 2 in by 3.5 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3.5 in dimension; and as fixed column about an axis perpendicular to 2 in dimension. Determine the safe central load with a factor of safety of 2 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it. SIR, PLS GIVE ME PROPER AND CORRECT ANSWER. THANKS
Determine the Pn of the following column assuming it had no moment on it and only an axial compression force: (f’c = 6000 psi, Grade 60 bars, h = 20”, b = 12” (i.e. rectangular section), tied column). Do not worry about calculating φ (phi factor). You can assume it is a short column. Also assume a reinforcement ration of 2% (ρg = 0.02).
Calculate the stresses in members AB, DF, and BD. Given:FAB = 51.22 kN (C)FDF = 50 kN (C)FBD = 32.98 kN (C)d = 0.05 m
Compute the co-ordinates for (Pnb, Mnb) and (Pub, Mub) for rectangular columns using h=24in b=14in Effective cover =3in. Reinforcement consists of 4-#9 bars on each side (totla of 8 bars) f'c=7000 psi fy=40000 psi. Use a yield strain of 0.004 for steel.
Problem 1. A W30 x 116 beam hasthe top flange restrained againstlateral displacement and rotationand has an unstiffened web. A pointload is applied to the top flange at2m. From the left support. The beamspans 12 m. Use A36 steel with yieldstrength of Fy = 248 Mpa. a. Compute the maximum value of point loadthat may be applied without web yieldingoccurring. b. Compute the maximum value of point loadthat may be applied without web cripplingoccurring. Properties of W30 x 116d = 762 mmK = 41.28 mmbf = 266.7 mmtf = 21.59 mmtw = 14.33 mm
2. A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is ‘RLL’ N/m2 of roof surface and roof covering is assumed to be ‘RDL’ N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900 e. Considering sag rods and tie rods at third points, what is the maximum moment about minor axis in N-m? (2 decimal places)