Problem 12: The sports car is traveling along a 30° banked road having a radius of curvature of p = 1000 ft. If the coefficient of static friction between the tires and the road is u= 0.2, determine the minimum safe speed so no slipping (slipping down) occurs. Neglect the size of the car.

Problem 12: The sports car is traveling along a 30° banked road having a radius of curvature of p = 1000 ft. If the coefficient of static friction between the tires and the road is u= 0.2, determine the minimum safe speed so no slipping (slipping down) occurs. Neglect the size of the car.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A helicopter flying with a velocity of 160km/h at elevation 500m above sea level dropped supplies to...

Q: For the following systems, identify the major components:a. a household refrigeratorb. a computerc. ...

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the exa...

Q: The 1986 disaster in the former Soviet Union at the Chernobyl nuclear power plant explosion sent abo...

Q: The angle of intersection of a circular curve is 45°30' and its radius is 198.17m. PC is Stationing ...

Q: A rectangular block of dimensior completely submerged in water it found to be 2542.8N. Find; (i) its...

Q: Problem 2. Investigate the adequacy of a 250mmx 250mm column, 3m high between lateral supports carry...

Q: 3. Design a rectangular R.C.C. beam using the following data: Beam span is 30' ft; f, = 60 ksi, f'̟ ...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

A: To Find ; (a) Static Head (b) Total Head

Q: *. Calculate the amount of lime and soda required to treat two million litre (M.L.) of hard water, c...

Q: Q1. Determine the components of reaction at support A and Reaction at support B. See Figure QI. PKn ...

Q: Compound axial member ABC has a uniform diameter of d = 2.1 in. Segment (1) is an aluminum [E1 = 10,...

Q: Sketch the shear and moment diagram for the beam loaded shown.

Q: a simply supported reinforced concrete beam has a Vf=140KN, determine if the beam can sustain the sh...

A: Given Fck=30mpa Ast 8-30# Area of concrete upto effective depth Depth = 600+100-110=590mm Using is c...

Q: A rectangular bar of length L has a slot in the central half of its length. The bar has width b, thi...

Q: The perpendicular distance between the parallel tangents of a reversed curve is 35 m. The azimuth fr...

A: Reverse Curve: A curve that consists of two simple curves which are joined together and curving in o...

Q: cted to a downward vertical load P at pi C, and D apply axial loads to members cross-sectional areas...

A: According to given data The three-member frame structure in Fig. P2.2-14 is subjected to a downward ...

Q: A cantilever truss carries a concentrated load P as shown in the figure below: e = tan (3/4) C V P W...

Q: Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wh...

Q: Calculate the ultimate axial load capacity of spiral column having a diameter of 500mm is reinforced...

A: The axial load ratio is defined as the applied axial load over the design axial load carrying capaci...

Q: The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Deter...

A: 5 bolts are given and their spacing is also given.. But distance of 1st bolt ? from edge is not giv...

Q: Write the shear and moment equations of each segment of the beam shown. Also, draw the shear and mom...

Q: A floor is supported by 75mm x 200mm wooden joists spaced @ 400 mm on centers with an effective span...

Q: 6.31 For the overhanging beam, compute the value of EIð under the 15-kN load. |15 kN 6 kN/m 3 m 5 m ...

Q: engineering economy

A: Given A = 1500, To find: A(P/A, 6%, 8)

Q: edule. The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gea...

Q: Prob. 2.3-7. For small loads, P, the rotation of "rigid" beam AF in Fig. P2.3-7 is controlled by the...

A: The change in length of a stressed structural member divided by the initial length of the unstressed...

Q: 1. A watershed has four rain gage stations. The annual rainfall depths recorded at three stations ar...

Q: 600 N B. 60° 30 50 mm

Q: From the given shear diagram below, where is the point of inflection located from the right end in m...

A: From given SFD - Shear Force Diagram ; we can draw Load diagram ; The load diagram image is attached...

Q: Calculate the moment (positive if counterclockwise, negative if clockwise) of the 370-N force on the...

A: Given- Force acting at an angle of 27 degrees = 370 N Two distances = 205 mm and 50 mm To Find- The ...

Q: Water flows steadily through the two relatively large tanks A and B as shown in Fig.1. The diameter ...

A: Using Torcellis equation for efflux. The discharge can be calculated. Then using conservation of mas...

Q: alculate the moment (positive if counterclockwise, negative if clockwise) of the 370-N force on the ...

Q: 52. Which type of inspection is more intensive involving examination of structural elements? A. O Mi...

Q: Given the parts of a spherical triangle: A = 82°, B = 100°, and c = 65°. Find angle C. Select one: O...

A: This is the problem on geodetic surveying where spherical triangles are formed over relatively large...

Q: Chapter 2, Problem 2/086 Five forces are applied to the beam trolley as shown. Determine the y-coord...

Q: A rhombus has an area of 54 cm2 and the ratio of base to altitude is 3: 2. Find the biggest interior...

Q: A section of highway has a speed-flow relationship of the form q = au2 + bu It is known that at capa...

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy...

A: Given data, P = 60 kN E of aluminium = 73 GPa Aluminum rod diameter = 16 mm Aluminum rod length (L...

Q: 1. An executive receives an annual salary of P600,000 and his secretary a salary of P180,000. A cert...

A: STEP 1 Salary per hour of executive = Annual Salary / Working hours a year Salary per hour of execut...

Q: *7-32.d The double T-beam is fabricated by welding the three plates together as shown. Determine the...

Q: For the figure shown, determine the horizontal and vertical components, respectively, of the hinge s...

A: Consider the member ABCD,

Q: the

A: A device for measuring corneal thickness that is installed on a slit-lamp is known as pachometer. It...

Q: Car A experienced engine failure the moment it enters a 2-km highway that has a constant grade of 4 ...

A: Solution :

Q: hollow cylinder 1 m in diameter and 2 m long weighs 3825 N. How many kN of lead (γ = 110 kN/m3) must...

Q: Question 1: A. Using Neat Sketchs, Ilustrate the main segemesnts of GPS System B. What are the main ...

Q: Determine the resultant and angle of inclination of the three forces if 0 = 30°. (1 500 N 300 mm 500...

Q: 4. A steel cylinder surrounded by a copper tube is subjected to a compression between parallel plate...

Q: From a reservoir A whose surface elevation is 225 m, water is pumped through 1200 m. of 300 mmø pipe...

A: Given data Diameter of pipe(d) = 300mm = 0.3m Length of pipe between 1 and 3 = 600m Length of pipe b...

Q: B 1.33 m Fy 2 m FH 0.85 Figure 2.13

Q: Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wh...

A: Given Data: The weight of the head-pipe is Wh=12 N The weight of the muffler is Wm=98 N The weight o...

Concept explainers

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.

Question

Problem 12: The sports car is traveling along a 30° banked road having a radius of curvature of p = 1000
ft. If the coefficient of static friction between the tires and the road is u= 0.2, determine the minimum
safe speed so no slipping (slipping down) occurs. Neglect the size of the car.
300

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The boat is traveling along the circular path with a speed of v = (0.0625t2) m/s, where t is in seconds. Determine the magnitude of its acceleration when t = 10 s.
A skier starts from rest on the 32° slope at time t = 0 and is clocked at t = 3.21 s as he passes a speed checkpoint 24 m down the slope. Determine the coefficient of kinetic friction between the snow and the skis. Neglect wind resistance. acceleration of the skier is 4.66 m/s^2
Find the angle of banking for a highway curve of 90 m radius for cars traveling at 128 Km/hr, if the coefficient of friction between the tires and the road surface is 0.40. What is the rated speed of the road? (In rated speed, the friction force between the tires and the road is zero)
The car starts from rest at s=0 and increases its speed at at=4 m/s². Determine the time when the magnitude of acceleration becomes 20 m/s². At what position s does this occur?
Situation 3. A road having a radius of 120m and has angle of 9.31 degrees from the horizontal. The center of gravity of the car is located 0.80m above the roadway and the distance between the two front wheels is 1.20m. If the car has a total weight of 15 KN, a. Compute the normal acceleration and the velocity of the car before overturning. b. If uk= 0.60, what is the velocity of the car without sliding? Please answer this with a complete solution and with a Free Body Diagram PLEASE. Thank you.
Find at what maximum speed a vehicle can move round a curve of 50 m radius without slip on a road banked with 1 in 10 slope? Take coefficient of friction between the tyres of the vehicle and the road equal to 0.4 Correct answer is 57.53 kph
A 100-Kg block is being pulled up a slope by an electric motor as shown. Determine the power required to move the the block at a constant speed of 1.5 m/s. The coefficient of friction between the block and the inclined surface is 0.30.
A vehicle is moving down at a speed of 80 kph along an inclined surface (G = 2%). If the coefficient of friction is 0.33, compute the braking distance in meters. Round off to two decimal places.
Subject: Dynamics of Rigid Bodies Topic: Banking curves and superelevation 2. Find the angle of banking for a highway curve of 90 m radius for cars traveling at 128 Km/hr, if the coefficient of friction between the tires and the road surface is 0.40. What is the rated speed of the road? (In rated speed, the friction force between the tires and the road is zero) Show the complete solution and its FBD.
For a car travelling with a speed of 50kph around a curve of radius 50m., Find the angle at which a road should be banked so that no friction is required.
! Show Full Solution ! *using CURVILINEAR MOTION Formula/s only! *use data given below Question: If the car passes point A with a speed of 20 m/s and begins to increase its speed at a constant rate of at =0.5 m/s2, determine the magnitude of the car’s acceleration when s = 101.68 m and x = 0.
TOPIC: Equation of Motion (NORMAL AND TANGENTIAL) Fn= Man Ft= Mat A road having a radius of 120m and has an angle of 9.31° from the horizontal. The center of gravity of the car is located 0.80m above the roadway and the distance between the two front wheels is 1.20m. If the car has a total weight of 15KN, Compute the normal acceleration and the velocity of the car before overturning. If uk= 0.60, what is the velocity of the car without sliding? PLEASE ANSWER WITH A COMPLETE AND DETAILED SOLUTIONS. THANK YOU