Problem 16.146-General plane motion: System of rigid bodies: Disk and rod on incline NOTE: This is a multi-part question. The uniform slender 2-kg bar BD is attached to the uniform 6-kg uniform disk by a pin at B and released from rest in the position shown. Assume that the disk rolls without slipping. 250 mm A 45° B 750 mm Problem 16.146.a - General plane motion: System of rigid bodies: Disk and rod on incline Determine the initial reaction at the contact point A. The initial reaction at the contact point A is D NA

Problem 16.146-General plane motion: System of rigid bodies: Disk and rod on incline NOTE: This is a multi-part question. The uniform slender 2-kg bar BD is attached to the uniform 6-kg uniform disk by a pin at B and released from rest in the position shown. Assume that the disk rolls without slipping. 250 mm A 45° B 750 mm Problem 16.146.a - General plane motion: System of rigid bodies: Disk and rod on incline Determine the initial reaction at the contact point A. The initial reaction at the contact point A is D NA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 2.00-kg slender rod shown is hanging in a vertical position and is pin-supported at point A. The slender rod is initially at rest until a 1.000-kg block C, strikes it at its end at point B.The block slides on a frictionless surface with a velocity of 3.50 m/s to the right. After the impact, it slides with a velocity of 1.250 m/s to the right, and the bar rotates with an angular velocity, ω'. Sketch the moment-impulse diagram 1. Which of the following gives the correct kinematic relationship relating the final velocity of the center of the rod, v'G, and its angular velocity, ω'? 2. Which of the following gives the closest value of the coefficient of restitution, e, between the block and the slender rod? 3. Which of the following gives the closest value of the magnitude of the horizontal impulse at the support at point A?
A slender 9-lb rod can rotate in a vertical plane about a pivot at B. A spring of constant k = 21 lb/ft and of unstretched length 6 in. is attached to the rod as shown in the figure. Knowing that the rod is released from rest in the position shown in the figure, determine its angular velocity after it has rotated through 90 degree .
A spool with radius R = 3 ft is released from rest on an incline with θ= 30◦, and its center, which coincides with its center of mass, is observed to reach a speed of 8 ft/s two seconds after release. If the spool rolls without slip,use impulse-momentum principles to determine the radius of gyration of the spool kG
Hey, please reply as soon as POSIBLE! Wheel A, of 30kg, is located in the position shown by the effect of idler wheel D (frictionless wheel) and the system rope-spring BC. The static coefficient of friction is 0.50 and the kinetic coefficient is 0.40 between all the contact surfaces. If the force exerted by the horizontal spring is 60 N: a) Determine whether or not wheel A is turning when a moment M of 60 Nm is applied at point G. b) If it is shown that under the previous condition the wheel is turning, calculate the new value of the moment M necessary for the wheel to keep turning in equilibrium. Also indicate the frictional force that is generated at point F under that condition.
Two disks A and B, of mass m 1 kg each and of radius 10 cm, are placed on a horizontal table. The disk A is launched in translation with a speed of 10 m/s along the y axis, B is at rest. The coefficient of kinetic friction between the disks is 0.5. The line of impact is at an angle of 60° with the x-axis. The moment of inertia of each disk around its center of mass is I = 1₂ = 0.005 kg.m². The coefficient of restitution between the two disks is e=0.6. a) Determine the velocities of the centers of the two disks, just after the impact. b) Calculate the angular velocities of the disks, just after the impact. c) Calculate the energy loss during the impact.
The double pulley shown has a mass of 15 kg and a centroidal radius of gyration of 160 mm. Cylinder A and block B are attached to cords that are wrapped on the pulleys as shown. The coefficient of kinetic friction between block B and the surface is μs = 0.2. Given that the system is at rest when the 200 N force is applied to cylinder A, determine the velocity of cylinder A as it strikes the ground.
A 1.6-kg tube AB can slide freely on rod DE which in turn can rotate freely in a horizontal plane. Initially the assembly is rotating with an angular velocity of magnitude w = 5 rad/s and the tube is held in position by a cord. The moment of inertia of the rod and bracket about the vertical axis of rotation is 0.30 kg.m2 and the centroidal moment of inertia of the tube about a vertical axis is 0.0025 kg.m2If the cord suddenly breaks, determine (a) the angular velocity of the assembly after the tube has moved to end E, (b) the energy lost during the plastic impact at E.
The 30-kg reel is mounted on a 20 kg cart. The reel is free to rotate about the axle O. The radius of gyration, kO, about the mass center, O, is 250 mm and a cable is wrapped around the inner hub of the wheel. The mass of the wheels on the cart and the mass of the cable may be neglected. The system is at rest when a force, P, of 50 N is applied to the end of the cable. a) Determine the velocity of the cart after 4 seconds m/s b) determine the angular velocity of the reel, in rad/s. [Correct answers are a) 4.0 m/s b) 16 rad/s
A collar with a mass of 1 kg is rigidly attached to a slender rod AB of mass 3 kg and length L = 600 mm. The rod is released from rest in the position shown. Determine the distance d for which the angular velocity of the rod is maximum after it has rotated through 90°.
A spool of mass 60 kg is supported on two rollers at A and B as shown in FigureQ1(c). Neglect the mass of the inelastic cable, friction and the mass of therollers at A and B. Knowing that a constant pulling force P is applied in order tounwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spoolis (604) mm, Appendix Ashows the examples of identifying the radius of gyration using student ID.(i) Determine the angular acceleration of the spool. (ii) Determine the pulling force P. (iii) Explain with calculation on ways to increase the acceleration of cablebeing pulled. [
A long ladder of length l, mass m, and centroidal mass moment of inertia I is placed against a house at an angle 0=0O. Knowing that the ladder is released from rest, determine the angular velocity of the ladder when 0=02. Assume the ladder can slide freely on the horizontal ground and on the vertical wall.
A spool of mass 60 kg is supported on two rollers at A and B as shown in Figure Q1(c). Neglect the mass of the inelastic cable, friction and the mass of the rollers at A and B. Knowing that a constant pulling force P is applied in order to unwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spool is (600+a) mm, where a = 8. Appendix A shows the examples of identifying the radius of gyration using student ID. Determine the pulling force P.