Problem 17.2:  Solve problem 17.1, but use a feed rate of 45 parts/min.  How does the reduced feed rate of the feeder-selector affect the operation of the assembly machine?   problem 17.1 listed below   (a) The feeder-selector device at one of the workstations of an assembly machine has a feed rate of 56 components/min and provides a throughput of one part in five. The ideal cycle time of the assembly machine is 6 sec. The low-level sensor on the feed track is set at 10 components, and the high-level sensor is set at 25 components. (a) How long will it take for the supply of components to be depleted from the high-level sensor to the low-level sensor once the feeder-selector device is turned off? (b) How long will it take for the components to be resupplied from the low-level sensor to the high-level sensor, on average, after the feeder-selector device is turned on? (c) What are the time proportions that the feeder-selector device is turned on and turned off?

Question

 

Problem 17.2:  Solve problem 17.1, but use a feed rate of 45 parts/min.  How does the reduced feed rate of the feeder-selector affect the operation of the assembly machine?

 

problem 17.1 listed below

 

(a) The feeder-selector device at one of the workstations of an assembly machine has a feed rate of 56 components/min and provides a throughput of one part in five. The ideal cycle time of the assembly machine is 6 sec. The low-level sensor on the feed track is set at 10 components, and the high-level sensor is set at 25 components. (a) How long will it take for the supply of components to be depleted from the high-level sensor to the low-level sensor once the feeder-selector device is turned off? (b) How long will it take for the components to be resupplied from the low-level sensor to the high-level sensor, on average, after the feeder-selector device is turned on? (c) What are the time proportions that the feeder-selector device is turned on and turned off?

Expert Answer

1 Rating

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Manufacturing Engineering

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: Determine the y-coordinate of the centroid of the shaded area.

A: To calculate the y co ordinate of the shaded region we use the standard formula of finding the y cen...

Q: hat the car 1920s model year (MY) look like? What systems it has, what it didn’t have.

A: In the 1920s, in the United States Henry Ford innovated mass-production techniques that became stand...

Q: 20-27. Rod AB is attached to collars at its ends by using ball- and-socket joints. If collar A moves...

A: Consider vB as the velocity of collar B, ωB as the angular velocity of collar B and rBA as the dista...

Q: Determine the force in members AD, CD, and CE of the truss shown when P1 = 6.6 kips and P2 = 10.6 ki...

A: Draw the free body diagram of the given truss,

Q: 19-37. Disk A has a weight of 20 lb. An inextensible cable is attached to the 10-lb weight and wrapp...

A: Given: The weight of disc A , WA = 20 lb The attached weight to the disc by cable, W= 10 lb The heig...

Q: Problem 4: A supply line contains a two-phase mixture of steam and water at 240 °C. To determine the...

A: Given data,

Q: 13-82. The 8-kg sack slides down the smooth ramp. If it has a speed of 1.5 m/s when y = 0.2 m, deter...

A: When y = 0.2 m, at this position the distance on the x-axis can be calculated as follows  

Q: 19-42. The vertical shaft is rotating with an angular velocity of 3 rad/s when 0 = 0°. If a force F ...

A: Consider the situation of the system which rotating about the z axis when the angle θ = 0o.

Q: While discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminat...

A: The statement given by technician A is correct as when the fail-safe function that is when the any e...

Q: Low-velocity steam with negligible kinetic energy enters a nozzle at 320°C, 3 MPa. The steam leaves ...

A: Given data as per the question At inlet steam temperature = 320°C At  inlet steam pressure = 3 Mpa V...

Q: RH2 = 43% What is the specific humidity of the air stream #1, w1 (lbm H2O/lbm air)? What is the spec...

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...

Q: F13–15. The 2-Mg car is traveling along the curved road described by r = (50e2") m, where e is in ra...

A: Express the path in polar coordinates. Assume radial acceleration to be directed towards the positiv...

Q: .For a steel alloy with .3% carbon, what would the percent of each phase be at 730°C and 725°C?

A: Let us consider a portion of Iron-Carbon diagram as shown below, For the 730 °C and 0.3% of carbon,...

Q: A ball and a socket joint forms a

A: A ball and a socket joint is a form of synovial joint in which socket swivel around the fixed ball. ...

Q: 2. When did Henry Ford founded Ford Company? when the first Ford Model T was launched?

A: The Ford company founded Henry Ford is founded in 1903. In July 1903 the first car is assembled in M...

Q: 19-35. The 2-kg rod ACB supports the two 4-kg disks at its ends. If both disks are given a clockwise...

A: Mass of the rod = 4 kg

Q: For W=800 N, P=200 N, and d=600 mm, determine the value of h consistent with equilibrium.

A: Given data: W=800 N, P=200 N, and d=600 mm Draw the free body diagram of the forces.

Q: A flat belt is used to transmit a couple from drum B to drum A. Knowing that the coefficient of stat...

A: The given belt pully system is showing below -  

Q: Name Problem #4 The wheel, with its attached hub weighs 80.5 lb and has a radius of gyration about i...

A: The free-body diagram of the wheel,  

Q: A rod assembly rotates around the z-axis. The mass C is 10 kg and its initial velocity is 7 m/s. A m...

A: Given data as per question Mass of the rod = 10 kg Velocity = 7 m/s Force =60 N M = 8t2+5  

Q: In order to move a wrecked truck, two cables are attached at A and pulled by winches B and C as show...

A: Given:  Tension in th cable AB, TAB = 2 Kips The free body diagram of the forces exerted at A is sho...

Q: Thank You!

A: Write the expression of film temperature. Write the property of air 5.75°C from the handbook.

Q: what is the purpose of having two accelerator pedal signals in an electronic throttle control system

A: The accelerator pedal signals are used to control the throttle valves in an electronic throttle cont...

Q: If the container were made from HDPE instead of PET, would it be safer to use or more dangerous to c...

A: PET stands for polyethylene terephthalate .it is tough in structure and clarity. this plastic is com...

Q: The pulley is pin-connected to block B at A. As cord CF unwinds from the inner hub with the motion s...

A: In the given figure it is mentioned that the point IC is the instantaneous center of rotation. Calcu...

Q: Psychrometric process A room has dimensions of approximately 10m x 10m x 3m. Assume the air inside t...

A: Given: Given: The temperature of air inside the room, T = 20 °C The pressure  of air inside the room...

Q: Determine the x and y components of each of the forces shown.

A: Consider the modified diagram for the provided one. Here in the diagram, the angles alpha, beta and...

Q: The epicyclic gear train consists of the sun gear A which is in mesh with the planet gear B. This ge...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: Water at 10°C (ρ = 999.7 kg/m3 and μ = 1.307 × 10−3 kg/m·s) is flowing steadily in a 5 -cm- diameter...

A: (a) In this problem, the velocity of the flow is not given but the flow is steady, therefore, it is ...

Q: For a 1095 steel alloy, what would the percent of each phase be at 730°C and 725°C?

A: Given alloy is steel 1095, for this steel percentage of the carbon present inside the steel is 0.95%...

Q: Consider a cubical water tank with a side length of 3 m. The tank is half filled with water, and is ...

A: Given Data: Consider the diagram shown below for the initial condition when there is zero accelerat...

Q: Problem 7 May you please explain each steps.   Thank you

A: Given data as per the question The pressure at inlet = 95 kpa Temperature at inlet = 300 k Combustio...

Q: A combination of kinematic pairs, joined in such a way that the relative motion between the links is...

A: A kinematic chain has numbers of kinematic links (rigid bodies) which are connected by the joints an...

Q: Name Problem #1 The wheel, having a two-foot radius, rotates at a constant velocity of 20 rad/s as s...

A: The given diagram is a four-bar mechanism of the crank rocker mechanism. Here, the ground is link #1...

Q: This is a dynamics problem. Answers: m = pi*h*R2 [k + (aR2)/2] , Iz = [(pi*h*R4)/2] * [k + (2a*R2)/3...

A: Let us consider an elemental shell at a radius r of thickness dr as shown below –  

Q: how many cars in the world in 1950? How many cars in each country? let say US, UK, France, Germany, ...

A: The total car manufactured in the world in 1950  were  10,577,426. The list of numbers of cars manuf...

Q: A 1.05% C steel is slowly cooled from 900 °C to temperature just slightly above 723 °C. Calculate th...

A: From the iron-carbide diagram understand that γ is used for austenite and Fe3C for cementite. Draw t...

Q: Specifically a dynamics problem. Question and diagram in pics below. Apparently the answers are aB=-...

A: The Instantaneous center of the ladder is shown below –  

Q: 19-55. The 15-lb rod AB is released from rest in the vertical position. If the coefficient or restit...

A: Given data: Weight of the rod, w = 15 lb Length of the rod, l = 2 ft Coefficient of restitution, e =...

Q: Why should you avoid recutting or grinding parts whenever possible?

A: When fabricating a weldment that is made up of all parts welded together there is the main problem t...

Q: a snowmobile is originally at the point with position vector 29m at 95degrees counterclockwise from ...

A: Given data  Position  = 29 m at 950 Velocity = 4.5 at 400 Acceleration = 1.9 at 2000 calculation pos...

Q: During a gust of wind, the blades of the windmill are given an angular acceleration of α=(0.2 θ) rad...

A: Given data as per the question Angular acceleration of α=(0.2 θ) rad/s2 Angular velocity of 5 rad/s

Q: May you please explain each steps.   Thank you

A: Drawing the P-V and T-S diagram of the cycle – The four-stroke engine cycle is shown in the figure. ...

Q: *20-20. Gear B is driven by a motor mounted on turntable C. If gear A is held fixed, and the motor s...

A: Consider ω is the angular velocity, ωz is the angular velocity in the z-direction, ωy is the angular...

Q: Consider a simple ideal Rankine cycle. What happens when the condenser pressure is raised while keep...

A: The Rankine cycle is an ideal cycle used for the prediction of the performance of the turbine system...

Q: Using the aluminum alloy 2014-T6, determine the largest allowablelength of the aluminum bar AB for a...

A: Given data, A column is given which is compressed by a vertical force P. the length of the column ne...

Q: This is a Dynamics question. Answers:  aG = 1.3 m/s2,                  alpha = 1.3 rad/s2,          ...

A: Given : Mass of spool = 100 kg The radius of gyration = 0.3 m The coefficient of static friction = 0...

Q: Write clearly and explain.

A: Understand that the uniform heat generated is one-dimensional, steady-state conduction. Write the ex...

Q: 19-49. The hammer consists of a 10-kg solid cylinder C and 6-kg uniform slender rod AB. If the hamme...

A: Given data:

Q: Type: E 3. A heat pump is designed to transfer heat into a building at a temperature of 25°C and rec...

A: Given: Source temperature , T1= 25 °C Sink temperature , T2 = 8 °C Solution: The idle heat pump  alw...