Problem 2) A pipe configuration is presented in the figure below. The support at point A is fixed. a) Calculate the moment about point A from the force F b) What component of the moment from a) is going in the direction AC? c) Determine the support reactions so that the rigid body (the pipe system) is in static equilibrium. 4 ft 3 ft 2 ft B AF (4i + 12j - 3k} lb

Problem 2) A pipe configuration is presented in the figure below. The support at point A is fixed. a) Calculate the moment about point A from the force F b) What component of the moment from a) is going in the direction AC? c) Determine the support reactions so that the rigid body (the pipe system) is in static equilibrium. 4 ft 3 ft 2 ft B AF (4i + 12j - 3k} lb

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.11P: A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and...

See similar textbooks

Similar questions

Three guy wires used in support system for television transmission tower that is 600 m tall. Wires A and B have tension as 60 kN whereas wire C has 30 kN as tension. What is the moment of wire forces about the base of the tower.
A traffic signal is shown in the figure below. There are two traffic lights A and B, attached to a 5m long overhang at a height of 6m from ground. The weight of each light is given to be 100N. Due to heavy winds there is a net force of 20N on each light acting along the z direction. Approximate the curved overhang by a straight line and determine the moment acting at the ground support G due to these forces.
Q/ Find the reaction forces at A and B, (A pin connection and B roller connection)? 120N/m
Solve the reaction forces.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
Find the reaction forces
Why is the wall reaction on the left side not considered in the calculation of force P
A uniform 80.0 N ladder 4.0 m long is placed against a frictionless wall with its base situated 2.0 m from the wall. Find the forces exerted by the wall and by the ground on the ladder.
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope 0.90 m above the floor (Fig. ). The ladders weigh 480 N and 360 N, respectively, and the center of gravity of each is at its center. Assume that the floor is freshly waxed and frictionless. (a) Find the upward force at the bottom of each ladder. (b) Find the tension in the rope. (c) Find the magnitude of the force one ladder exerts on the other at point A. (d) If an 800 N painter stands at point A, find the tension in the horizontal rope.
A beam resting on two pivots has a length of L = 6.00 mand mass M = 87.0 kg. The pivot under the left end exerts a normal force n1on the beam, and the second pivot placed a distance ℓ = 4.00 m from the left end exerts a normal force n2. A woman of mass = 61.5 kgsteps onto the left end of the beam and begins walking to the right as in the figure below. The goal is to find the woman's position when the beam begins to tip. (b) Where is the woman when the normal force n1 is the greatest?x = ________m(c) What is n1 when the beam is about to tip?__________ N(d) Use the force equation of equilibrium to find the value of __________n2 when the beam is about to tip. __________N(e) Using the result of part (c) and the torque equilibrium equation, with torques computed around the second pivot point, find the woman's position when the beam is about to tip.________x = m(f) Check the answer to part (e) by computing torques around the first pivot point.________x = mExcept for possible slight…
In the simple cage system in the figure, which of the following is the absolute value of the force carried by the CE element in kN?