Problem 2: A uniform concrete slab of total weight 100 kN is to be attached as shown to two rods whose lower ends are on the same level. O Determine the tensile force of the aluminum rod so that the slab will remain level. ® Determine the ratio of the area of aluminum rod to the steel rod so that the Steel E=200 GPa L=6m Aluminum E=69 GPa L=4m slab will remain level. Determine the vertical displacement of the concrete slab if the aluminum rod has a cross sectional area of 320 mm2, with the slab remaining at horizontal level. 3 m 6 m m

Problem 2: A uniform concrete slab of total weight 100 kN is to be attached as shown to two rods whose lower ends are on the same level. O Determine the tensile force of the aluminum rod so that the slab will remain level. ® Determine the ratio of the area of aluminum rod to the steel rod so that the Steel E=200 GPa L=6m Aluminum E=69 GPa L=4m slab will remain level. Determine the vertical displacement of the concrete slab if the aluminum rod has a cross sectional area of 320 mm2, with the slab remaining at horizontal level. 3 m 6 m m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the ff. 1. Location of max deflection 2. Slope at point a and b 3. Max deflection Show complete solution
Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute the DESIGN BASE SHEAR (V = Cv*I*W /R*T). B. Compute the Minimum DESIGN BASE SHEAR (V =0.11Ca*I*W).
An R.C. Column footing 2.26 m in square shape is to rest 1.5 mbelow level ground level is on cohesive soil. The unit weight is17.6kN/m3. What is the safe load if cohesion is 30kN/m3Factor of safety 2.4? Angle of internal friction 33° by IS code.
Determine the normal stress in each of the cables? (MPa) a. 85.7 b. 75.7 c. 65.7 d. 55.7 If the cables elongated by 1 mm, what is the vertical displacement of the precasat slab? (mm) a. 1.758 b. 1.658 c. 1.458 d. 1.558 What is the tensile force in each of the cables? (kN) a. 5.98 b. 4.98 c. 7.98 d. 6.98 SOLVE ALL AND WILL GET A LIKE <3 ps: unit weight of concrete is 24kn/m^3
Calculate the width of the concrete wall that is necessary to prevent the wall from sliding and the horizontal reaction acting on the system, Rx. The unit weight of the concrete is 23.6 kN/m^3 and the coefficient of friction between the base of the wall and the foundation soil is 0.42. Use 1.5 as the factor of safety against sliding. Will it also be safe from over turning?
Find P to keep the 600N roller from rolling down the rough inclined surface. *use 3 decimal places all throughout the solution.
7.compute failure function 8. compute principal stress
A soil sample (sand) obtained from trench has water content of 38%. The specific graavity of solid is 2.65. Determine the maximum permissible upward force if factor of safety is 3. a. 1.007 b. 0.822 c. 0.274 d. 0.107
USING DOUBLE INTEGRATION METHOD Consider 250 mm x 250 mm (bxh) mm section and e = 100000 MPa DETERMINE VERTICAL REACTION AT B Values:A = 9.4 MB = 5.5 MC = 10.6 KN/MD = 33 KN
The distance between two points A and Balong the longitudinal wall of a masonrybearing structure is L, and its settlementdifference is △ s, then △ s/L is ( )◼Settlement◼Differential settlement◼Tilt◼Local tilt
A 6 m concrete slab of weight W is to be supported at one end by a steel rod 3 m long having a modulus of elasticity of 200000 MPa and the other end by an aluminum rod 4 m long with a modulus of elasticity of 70000 MPa. The lower ends of the rods are initially at the same level.1. Which of the following gives the ratio of the area of the aluminum rod to that of the steel rod so that the slab will remain level after it is attached to the rods? a. 2.81b. 3.81c. 1.81d. 4.812. Which of the following gives the elongation of the steel bar if it has a diameter of 25 mm when W = 30 kN. a. 0.46mmb. 0.66mmc. 0.56mmd. 0.76mm3. Which of the following gives the strain of the aluminum rod? a. 0.000215b. 0.000315c. 0.000115d. 0.00445
Wooden posts (E=1,800,000 psi) are used for a retaining wall, each post is 6in x 6in. If the soil pressure along a post varies linearly from zero at A to a maximum at B, determine the displacement at the top of the post. Assume B is fixed and A is free. Report your answer in inches to three decimal places.