Answer only problem 3. Provide detailed free-body diagrams or sketches. " PROBLEM 3In Problem 2, what is the magnitude and direction of the force exerted bytugboat B on the cargo ship if the single force that replaced the two forces exerted bythe tugboats is 35,000N in the horizontal direction? Solve using both the a) forcetriangle method and b) force component method.Renzkeys | TWL PROBLEM 2Two tugboats are towing a cargo ship as shown. Tugboat A exerts a force of15000N and tugboat B exerts a force of 20,000N. Replace the forces exerted by thetugboats with just a single force. What is the direction of this force?AB

Answered: Image /qna-images/answer/6c1523aa-ad4b-40e3-8b35-d60192bdf0c3.jpg

PROBLEM 2 Two tugboats are towing a cargo ship as shown. Tugboat A exerts a force of 15000N and tugboat B exerts a force of 20,000N. Replace the forces exerted by the tugboats with just a single force. What is the direction of this force? A B

PROBLEM 2 Two tugboats are towing a cargo ship as shown. Tugboat A exerts a force of 15000N and tugboat B exerts a force of 20,000N. Replace the forces exerted by the tugboats with just a single force. What is the direction of this force? A B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the value of El y at the right end of the overhanging beam. a = 4.4 m, b = 2.8 m, Wo =…

Q: → A reinforced cement concrete pile weighing 30 kN (including helmet and dolly) isuriven by a drop…

Q: A pressure-vessel is fabricated by gluing the circular plate to the end of the vessel as shown in…

A: Internal pressure = P = .45MPa Diameter = d = 450mm Thickness = t = 10mm Side thickness = t' = 20mm

Q: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB BC BD…

Q: Determine the force in each member of the space truss and state if the members are in tension or…

Q: PROBLEM TO SOLVE: 600 mm 400 mm +6-25mm diam. 90 mm Using fc' = 28 MPa, Mmax = +320 kNm Determine…

Q: If line OC has an AZIMn of 83° 44’ 19” and line OD has an AZIMs of 56° 21’ 06”, determine the angle…

Q: 8. The specific gravity of oil is 0.85., what is its specific weight in lb/ft^3? 55 lb/ft^3 53…

Q: Current Attempt in Progress Oil flows through the system shown in the figure below with negligible…

Q: In the recent earthquake, the velocity of P-waves is 3.12km/s while it traveled on the soil whose…

Q: * Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when…

Q: Explain the process of Hydrological Cycle.

A: The water cycle describes the movement of water through the land, oceans, and atmosphere of Earth.…

Q: 5(y")² + 10(y')³ = 3x -y d²y dt² y"" +3y' +2y=x² 8²v ἂν = +1 ay² ax d²y dx² +(5t + 1)² = 0 DEPENDENT…

A: Whenever we differentiate a variable with respect to another variable, the variable which gets…

Q: moisture

A: Given S1=40% ɣd1=14.50 kN/m3 s2=70% ɣd2=17.89 kN/m3 w1=w2=w

Q: Determine the forces in each members of the truss

A: Given: A truss Required: Force in each member of the truss

Q: 1. Assuming the concrete is uncracked, compute the bending stresses in the extreme fibers of the…

Q: For the cantilever beam shown. find the value of Normal stress due to axial load at :point F 10 m 4…

A: Normal stress is the stress which get generated due to the force acting on normal or perpendicular…

Q: Find a) Shear diagram reaction 10 ил ↓ diagram Max (+ ve & -ve) moment 2 lo kN/m moment 23 lokN ↓

A: To draw SFD and BMD

Q: Please answer this problem instead of the one stated in the pic. Determine the force in members ED…

A: All member dimensions and angles are given. Joint loads are given. First find out support reactions…

Q: all

Q: 19. A compressed liquid in a container has a volume of 1 liter at a pressure of 1 MPa and a volume…

A: Given data in question Pressure 1 and 2 MPa Volume = 1 and 0.995 litre Volume modulus of elasticity…

Q: So there's 3 forces on a body and they're not parallel and they intersect at a point so their angles…

Q: Analyze the truss shown in figure. #T GHA 25KN JOKN g A I вт 'K' F 6M Not * GRA B+

A: Given figure shows the truss It is required to calculate the forces in all the members of truss.

Q: Q#2 What is meant by "canal lining", and what are its advantages? briefly explain shotcrete lining.…

A: [ NOTE - As per Bartleby guidelines, we are directed to solve only 1 question at a time if they are…

Q: what is the minimum number of water closets for an industrial building with 250 occupants? show…

A: Reference : Water Management, Plumbing Fixtures. Given : The Table for Industrial building is given.…

Q: Can the system in given figure be in static equilibrium in the position shown? The uniform bar AB…

Q: 2. Convert the following azimuths to their equivalent bearings: a. 85° 57' 10" b. 146° 29' 37" c.…

A: Convert the azimuth to their equivalent bearing.

Q: cd Wo b

Q: For each of the indeterminate frames above please draw the deformed geometry and moment diagram.…

Q: Point A is between points B and C. The distances of B and C from point A are 1000m and 2000m…

Q: 2) Is a W21x55 beam adequate for loading conditions shown below. The beam is continuously braced, E…

A: Given Data: The Young's modulus of elasticity is E=29,000 ksi. The tensile strength is Fy=50 ksi.…

Q: Specify where the force acts, measured from end B. Express your answer using three significant…

A: Given : F1 = 550 lb , F2 = 200 lb, F3 = 520 lb To Find : Specify where force acts , measured from…

Q: Draw according to scale. 12km, South 11mm,12\deg South of East 22(m)/(s),45\deg North of West 75cm,…

Q: SAQ 6 (Problem) The two mooring cables exert forces on the stern of a ship as shown. Determine the…

A: Given data Find magnitude of resultant and its direction.

Q: Determine the magnitudes of cable 2 and 3 for equilibrium. Consider force at cable 1 is 300N and W…

Q: 12. A liter of water weighs about 97,500 dynes, what is its mass in kilograms?.

Q: Situation #2 Classify each of the structures as statically determinate, statically indeterminate, or…

Q: groundwater sample from well #25 has this information, express the hardness of the p

A: Hardness is due to Ca and Mg so,Hardness=Cocentration of Ca2+ and Mg 2+Given COnc of Ca2+=123mgLCOnc…

Q: 25. A body weighs 1000 lbf when exposed to a standard earth gravity g = 32.174 ft/s^2. What is its…

Q: A three-ply asphalt felt and gravel roof over 2-in.-thick insulation board is supported by…

A: Self weight of insulation - 3 lb/ft2Self weight of asphalt roofing - 5.5 lb/ft2Unit weight of RCC -…

Q: 6. The length of the basketball court from MIT's Gym was paced by a CE student whose pace factor is…

A: Given a basketball court Length of a basketball court =28 m(known value) pace factor of basketball…

Q: The flow rate in a wide rectangular open channel is 2.0 m³/s per metre width. The channel bed slope…

Q: rovide neat answer using slope deflection or the most suitable for you

Q: From the field notes of a closed traverse shown for the linear error of closure and relative error.…

A: Given: STATION DISTANCE (m) AZIMUTH AB 233.10 122° 30' BC 242.05 85° 15' CD 191.50 20° 00'…

Q: Determine the horizontal deflection at joint C of the truss by virtual work method. Use E = 10,000…

A: A=5in2 E=10000ksi To find horizontal deflection at point C

Q: A beam 100 mm wide is to be loaded with 20 kN concentrated loads spaced uniformly at 0.40 m on…

A: width of beam =100 mm concentrated load =20 KN The span of the beam =10 m Allowable bending stress=…

Q: Determine the horizontal deflection at joint C of the truss by virtual work method. Use E =…

A: L1=4ft L2=5ft L3=12ft E=10000ksi to find horizontal deflection at point C

Q: A rough pipe has a diameter 80 mm. the velocity at a point 30 mm from the wall is 30% more than the…

A: Rough pipe Diameter, d = 80mm Velocity at 30mm from wall = v1 Velocity at 10mm from wall = v2 As…

Q: Shown below is the table of minimum requirements for Water Closets. What is the minimum number of…

A: Given, Industrial building with 400 occupants To find : Minimum number of water closets

Q: Question A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

Question

Answer only problem 3. Provide detailed free-body diagrams or sketches. "

PROBLEM 3
In Problem 2, what is the magnitude and direction of the force exerted by
tugboat B on the cargo ship if the single force that replaced the two forces exerted by
the tugboats is 35,000N in the horizontal direction? Solve using both the a) force
triangle method and b) force component method.
Renzkeys | TWL

PROBLEM 2
Two tugboats are towing a cargo ship as shown. Tugboat A exerts a force of
15000N and tugboat B exerts a force of 20,000N. Replace the forces exerted by the
tugboats with just a single force. What is the direction of this force?
A
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

As shown, a uniform beam of length d = 1.80m and mass 21.3kg is attached to a wall with a pin at point B. A cable attached at point A supports the beam. The beam supports a distributed weight W2 = 345N/m . If the support cable can sustain a maximum tension of 1250N , what is the maximum value for W1? Under this maximum weight, what is FBy which is the vertical component of the support's reaction force at point B? Show calculations. Will rate if correct.
1. Force A has a magnitude of 200lb, and points 35° N of W. Force B points 40° E of N. Force C points 30° W of S. The resultant of the three forces has a magnitude of 260lb, and points 85° S of W. A) what is the magnitude of force B? B) What is the magnitude of force C?
As shown in the figure a rigid beam with a negligible mass is pinned at O and supported by 2 rods identical except for length. If P=30KN, find the load in rod A and B in KN. If rod A elongates by 2mm how much is the elongation of rod B in mm?
If the center of gravity of a ship in the upright position is 10m above the center of gravity of the portion under water, the displacement being 1000 metric tons, and the ship is tipped 30 causing the center of buoyancy to shift sidewise 8m. a) Is the moment righting or overturning and why? B) What is the value of this moment in kg m?
A horizontal force P acts on the top of the 30N block having a width of 25 cm and a height of 50 cm. If the coefficient of friction between the block and the plane is 0.33. What is the value of P for motion to impend?
Need help experts. The rigid body shown in the figure is subjected to the indicated force system. Determine the forces applied at points A and E that equal the applied force system.Data: β = 48°; a = 6,6 m; b = 8,9 m; F = 31 kN; P1 = 20,743 kN; P2 = 23,037 kN The force applied at point A is FA = ? Answer kN and the force applied at point B is FB = ? Answer kN.
Problem 7. Figure shows a dam 30.5m long that retains 8m of fresh water and is inclined at an angle 0 of 60’’. Calculate the magnitude of the resultant force on the dam.a. 18.06 MNb. 16.06 MNc. 14.06 MNd. 12.06 MNe. 11.06 MNf. 8.06 MN
2. A beam rests on a fulcrum, 1.2 m from one end. A weight of 350 kg is suspended from this end causing the beam to balance. If the weight of 350 kg is suspended on the opposite end of the beam, it is necessary to suspend a 1000 kg weight on the first end in order to affect an even balance. Find the length of the beam in mm.
The modulus of elasticity of the cantilever beam shown in the figure = 210.000 MPa and the length L = 5 m. Since q = 10 kN/m and 1=1,5x10-6 mm* end B collapses and calculate the rotation. 9 1 B L
As shown in this image, water fills a tank with a sloped side, which has a flat, rectangular gate of height 6-ft and width 7-ft. The hinge along the top allows the gate to open when a force P is applied. If you neglect friction and the weight of the gate, what is force, P, in lb-f required to open the gate?
Find the magnitude and direction of the resultant of two concurrent forces of 75 and 100 lb acting on a body at an angle of 110° with each other as in the figure below.
If the center of gravity of a ship in the upright position is 10 m above the center of gravity of the portion under water, the displacement being 1000 metric tons, and the ship is tipped 30° causing the center of buoyancy to shift sidewise 8 m. a) Is the moment righting or overturning and why? b) What is the value of this moment in kg·m?