PROBLEM 2: Using METHOD OF SECTIONS, determine the forces of the members IH and BH in kN of the truss shown. Indicate if tension or compression. Note: FBD FOR SECTIONED PART OF THE TRUSS IS REQUIRED WITH CLEAR ILLUSTRATIONS OF THE SECTIONED FORCES BEFORE ANY NUMERICAL SOLUTIONS. 40 kN 30 kN 20 kN 20 kN G F 4 m 16 m, 4@4m

PROBLEM 2: Using METHOD OF SECTIONS, determine the forces of the members IH and BH in kN of the truss shown. Indicate if tension or compression. Note: FBD FOR SECTIONED PART OF THE TRUSS IS REQUIRED WITH CLEAR ILLUSTRATIONS OF THE SECTIONED FORCES BEFORE ANY NUMERICAL SOLUTIONS. 40 kN 30 kN 20 kN 20 kN G F 4 m 16 m, 4@4m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the force in members DC, HI, and JI of the truss. State if the members are in tension or compression. Take that P1 = 1070lb and P2 = 1710lb . Suggestion: Use the sections shown. (Give neat and clean answer I will give like else dislike)
Find the forces in members EF, KL, and GL for the Fink truss shown. Answer using method of section.
Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension or compression. You are required to tabulate the member forces in the table below.
Solve Prob. 6.39 for P = 0 and Q = (-900 N)k.(Reference to Problem 6.39):The truss shown consists of nine members and is supported by a ball-and-socket at B , a short link at C , and two short links at D. (a) Check that this truss is a simple truss, that it is completely constrained, and that the reactions at its supports are statically determinate. (b) Determine the force in each member for P= (-1200 N)j and Q = 0.
Determine the forces in members EF, GH and GI of the truss shown & designate whether the member is Tension or Compression. EF = 5 kips (T), GI = 10.4 kips (T), GH = 33 kips (T)EF = 5 kips (C), GI = 10.4 kips (C), GH = 33 kips (T)EF = 5 kips (C), GI = 10.4 kips (T), GH = 33 kips (C)EF = 5 kips (T), GI = 10.4 kips (C), GH = 33 kips (C)EF = 5 kips (C), GI = 10.4 kips (C), GH = 33 kips (C)EF = 5 kips (T), GI = 10.4 kips (T), GH = 33 kips (C)EF = 5 kips (C), GI = 10.4 kips (T), GH = 33 kips (T)EF = 5 kips (T), GI = 10.4 kips (C), GH = 33 kips (T)
The truss carries the loads as shown in Figure 2. The truss is supported by pin at A and smoothroller support at G. (b)By using method of section, determine the force in members CD, CJ and KJ of the truss.State if the members are in tension or compression.
Using the method of joints, determine the force in each member of the truss shown. State whether eachmember is in tension or compression. You are required to tabulate the member forces in the table below.
For the truss loaded and supported as shown in figure, determine the forces in member CD, DG and GH using method of sections.
Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension or compression. Complete solution
Solve Prob. 6.67 assuming that the 9-kip load has been removed.(Reference to Problem 6.67):The diagonal members in the center panels of the truss shown are very slender and can act only in tension; such members are known as counters. Determine the force in member DE and in the counters that are acting under the given loading.
Determine the force in bars BD, CD and DE of the nacelle truss shown in figure.
How do I determine the force in each of members in the truss shown? The loads are p=20kips and Q=50kips