PROBLEM 2. The light rigid bar ABCD shown in Fig. P-252 is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 41. 29 KN is applied. Hint: convert the distance of each member into mm, area of steel and aluminum into mm^2, & E into MPa.. Steel L-3ft A - 0.5 in E- 29 x 10° psi 4ft Aluminum L-4R A-0.75 in E- 10 x 10 psi 2 ft Figure P-252

PROBLEM 2. The light rigid bar ABCD shown in Fig. P-252 is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 41. 29 KN is applied. Hint: convert the distance of each member into mm, area of steel and aluminum into mm^2, & E into MPa.. Steel L-3ft A - 0.5 in E- 29 x 10° psi 4ft Aluminum L-4R A-0.75 in E- 10 x 10 psi 2 ft Figure P-252

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 73AP: Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m...

See similar textbooks

Similar questions

Consider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of 5.3 1010 N/m2. Steel has a Youngs modulus of about 2.000 1011 Pa. How much stress would cause a piece of steel to experience the same strain as the nanotube?
Review the relationship between stress and strain. Can you find any similarities between the two quantities?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Find the elongation of a rod made of aluminum and copper under a tension of 5.8×103 N. The dimensions of the rod are R=0.5 cm, LAl=10.5 m, LCu=5.5 m (Young moduli are 7.0×1010 Pa for Al and 11×1010 Pa for Cu)
A 45 cm x 45 cm square plate ABCD of uniform thickness is supported by three vertical strings. The first string is located at B, the second is located 15 cm from A alongside AD and the third is at the point midway of side CD. What percent of the load is carried by the second support?
A material of Poisson's ratio 0.5. If a uniform rod it suffers a longitudinal strain of 2*10 -3, what is the percentage increase in volume?
What is the indentation diagonal length in in, when a load of 0.60 kg produces a Vickers HV of 400?
For the beam and loading shown, determine the maximum absolute value of bending moment and shear.
The upper surface of a cube of gelatin, 5.0 cm on a side, is displaced by 0.64 cm by a tangential force. If the shear modulus of the gelatin is 940 Pa, what is the magnitude of the tangential force?
(I) A sign (mass 1700 kg) hangs from the bottom end of avertical steel girder with a cross-sectional area of 0.012 m2(a) What is the stress within the girder? (b) What is thestrain on the girder? (c) If the girder is 9.50 m long, howmuch is it lengthened? (Ignore the mass of the girder itself.)
A block of copper has surface area, A=10cm2 effected by its upper and lower surfaces by an opposite forces (F=50N) which cause a shearing stress, Calculate the shearing angle, under that shearing forces .