Problem 2. This is a drive mechanism to release a main clutch. Determine the force that should be applied to the pedal (force Fpedat) in order to generate a force of 500N, which acts on the disk (Faisk N). aj = 100 mm; az = = 500 120 mm; bị =150 mm; bz = 130 mm; ci = 200 mm; c2 = 420 mm. Disk pedal disk

Problem 2. This is a drive mechanism to release a main clutch. Determine the force that should be applied to the pedal (force Fpedat) in order to generate a force of 500N, which acts on the disk (Faisk N). aj = 100 mm; az = = 500 120 mm; bị =150 mm; bz = 130 mm; ci = 200 mm; c2 = 420 mm. Disk pedal disk

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter37: Clutches

Section: Chapter Questions

Problem 7RQ: Torsional coil springs in the clutch disc_____. a. cushion the driven disc engagement rear to front...

See similar textbooks

Similar questions

Torsional coil springs in the clutch disc_____. a. cushion the driven disc engagement rear to front b. are the mechanical force holding the pressure plate against the driven disc and flywheel c. absorb the torque forces d. are located between the friction rings
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
The shaft pulley system has a universal joint at point 0. So it is supported by a slide at point A bearing and fixed support at point C. There is a mass of 12kg on the pulley and subject to the belt tensions but the mass of the shaft is negligible. a) what is the static equilibrium equations for the assembly. b) draw the FBD of the assembly. c) show the assembly and the FBD for the components
Dynamic Forces Analysis:- Present a clearly labelled free body diagram for each rod and the slider;- Calculate the magnitudes and directions of all reaction forces at the instant shown using accelerations obtained in acceleration analysis part;- Calculate the instantaneous torque, T, required to drive the mechanism at the instant shown.
The figure shows a mechanism that raises packages in a transfer mechanism. A 200-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 287 rpm CCW. At the position shown the crank OA is vertical and the output link OB is horizontal. we need to determine the torque required from the motor at the crank O2A and the force in member AB The weights of the links are negligible. 50mm 450mm 200 N 200 mm B. 374 mm 300mm X The angular velocity of the link OĄBD in rad/s is = Choose... + The magnitude of the velocity of point D in m/s is = Choose... + The torque required from the motor at the crank O2A in N.m is = Choose... : The force in member AB in N is = Choose... +
to calculate the radial force acting upon the clutch face, shouldnt the force of 1 shoes be calculated, multiplied by 4 then subtracted the spring stiffness which is also multiplied by 4?
Describe the static force analysis of the follow ing mechanisms by considering the effect of sliding friction, (a) Slider in equilibrium under the action of concurrent forces (b) Slider in equilibrium under the action of non concurrent forces.
Find the true magnitude and direction of forces on the wheel and cable members at static equilibrium
Statics Problem 6.134 - Determine couple M applied to crank AB when (a) α = 60 degrees, (b) α = 90 degrees
The figure below shows the four-bar mechanism given with ABCD. Of 2000 N force In order to have a static balance when applied; (by graphic method) a) Find all the forces affecting the limbs. b) Find the magnitude and direction of torque T.
Why does the single thrust bearing have two couple moments? is it not supported by the tension cable at CB?