Problem 3N=42Arm-N=24-NA-18-HN18РEN20-NG-40N18G NGA is driven cw@ 1066-6N₂₁ = 18NB=24Nc - 42No = 20NE=40NF19NG = 12= 122= 18NH=• Determine notational speed anddirection of year G"

Given data as per question speed of A gear =1066.6 rpm (clockwise)

Problem 3 Arm- N=24 P C N=42 -N-18 -H N18 No 20 -NG -40 N18 N₁ = 18 Ne=24 Nc-40 A is driven cw@ 1066.6 No=20 No = 40 N-18 NG 12 NH=18 -G N₁₂ = 12 • Determine rotational speed and direction of year G

Problem 3 Arm- N=24 P C N=42 -N-18 -H N18 No 20 -NG -40 N18 N₁ = 18 Ne=24 Nc-40 A is driven cw@ 1066.6 No=20 No = 40 N-18 NG 12 NH=18 -G N₁₂ = 12 • Determine rotational speed and direction of year G

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and a torque of 1 kN.m. The member is made of steel the Ultimate Tensile Strength 440 MPa, Yield Tensile Strength 370 MPa. With a safety factor of 4, kt = km = 1.5 and keyway stress consternation is presented. According to the maximum shear stress theory, the shaft diameter will be: a. 160 mm b. 74 mm C. 145 mm d. 92.5 mm e. 60 mm f. 66 mm
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
The values given for a radial plain bearing are:Shaft diameter = 40 mm, bearing width = 30 mm, Pem = 6 N / mm2, Radial force = 2 KN, Ty = 45 C, oil: ISO VG 15, bearing clearance = 35 µm, dynamic viscosity for given oil and temperature = 12 m Pa. sRequired:a) What is the working cycle of the shaft?b) Find the Sommerfeld number.
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 290 kW(ii) speed = 60 rpm,(iii) Maximum shear stress = 65 MPa(iv) diameter ratio = 1.5(v) The maximum value of the twisting moment is 40% greater than its mean. The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
-Two shafts made of plain carbon steel are connected by a rigid protective type flange coupling. The shafts are running at 500 r.p.m. and transmit 25 kW power. Design the coupling completely for overload capacity 25 percent in excess of mean transmitted torque capacity. Assume the following permissible stresses for the coupling components : Shaft — Permissible tensile stress = 60 MPq; Permissible shear stress = 35 MPa Keys — Rectangular formed end sunk key having permissible compressive strength = 60 MPa Bolts — Six numbers made of steel having permissible shear stress = 28 MPa Flanges — Cast iron having permissible shear stress =12 MDA~
a steam engine runs at 150rpm. its turning moment diagram gave the areas in mm2 taken in order above and below the mean torque line is 500,250,270,390,190,340,270,250, the scale for turning moment is 1mm=500mnm, 1mm=5’ if the fluctuation of speed is not to exceed +or-1.5% of mean, determine a suitable diameter and cross-section of the rim of flywheel with axial dimension equal to 1.5times the radial dimension. the hoop stress is limited to 3mpa and the density of material of flywheel is 7500kg/m3.
It has a full-slide type bearing rotating at a speed of 1975 rpm.A load of 5693 N is applied. SAE 40 oil in bearing at 60C inlet temperatureplanned to be used.Shaft and bushing diameters in bearing with tolerance data 41−0.010 respectively+0.000mmand 41.125−0.000+0.100 mm.Average radial clearance mounting for this bearing with bush length 20.50 mmCalculate the following;a) Bearing characteristic number,b) Minimum lubricant film thickness,c) Eccentricity value,d) coefficient of friction,e) Average oil film temperature andf) Find the Tmax temperature value.
You are asked to design a plain surface journal bearing to carry a steady radial load of 5.75 kN while the shaft rotates at 950 rpm. The shaft stress analysis determines that an acceptable nominal diameter of the journal is 62.5-mm and an l/d ratio is 1. The shaft is part of a machine requiring good precision. So a minimum radial clearance cmin= 0.040 mm seems appropriate. We shall use SAE 30 oil as a lubricant, at an inlet temperature of 45 oC. Analyze the hypothetical bearing,a) Determine the operating temperature Tave, and operating viscosity μave. b) Determine the minimum film thickness, ho, temperature rise of the lubricant, ΔTC, the total oil flow, Q, and side flow Qs in [mm3/s], the maximum film pressure Pmaxdeveloped in [MPa]. c) Determine the power loss, Hloss in [W], friction torque, Tf in [N-m] d) For minimum radial clearances, perform a design assessment using Trumpler’s criteria.
A bearing is subjected to a radial force of 8kN and a thrust force of 3 kN. Thevalues of X and Y factors are 0.56 and 1.5 respectively. The shaft rotates at 1200 RPM. The diameter of the shaft is 75mm and Bearing no. 6315 (C= 112000N) is selected for this application. Estimate the life of this bearing with 90% reliability.
The armature shaft of a 50 kW, 580 rpm electric motor, mounted on two bearings A and B, is shown in Fig. The total magnetic pull on the armature is 5 kN and it can be assumed to be uniformly distributed over a length of 400 mm midway between the bearings. The shaft is made of steel with an ultimate tensile strength of 770 N/mm2 and yield strength of 580 N/mm2. Determine the shaft diameter using the ASME code if, kb=1.5 and kt=1.0 Assume that the pulley is keyed to the shaft.