Problem 3Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal stress for thematerial is 0allow =200 MPa10 mm40 mma60 mm-10 mm200 mm

The centre of gravity of the clamp is given by,

Answered: Problem 3 Determine the maximum ram…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the normal stress due to flexure at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 5/8 in. thick and is connected to the vertical rod by a 3/8-in.-diameter bolt. Determine (a) the average shearing stress in the bolt, (b) the bearing stress at C in member BD.
Two 160 mm * t cover plates are welded to two cahnnels 200 mm high to form the cross section of the beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 2.06*106mm4. a)Determine the support reactions. b)Draw the shear force and bending moment diagrams. c)If the allowable bending stress of the beam is 255 MPa, find the required thickness t of the plates to safely support the load.
The wall hanger has a thickness of 0.25 in. and is used to support the vertical reactions of the beam that is loaded as shown. If the load is transferred uniformly to each strap of the hanger, determine the state of stress at points C and D on the strap at A. Assume the vertical reaction F at this end acts inthe center and on the edge of the bracket as shown.
10m beam is loaded with point load P1 = 100N at 2m from the fixed end support. A distributed load (W1) was also imposed with a magnitude of 100 N/m as shown. The beam is supported by a pin and a roller at locations specified in the free body diagram. what are the reactions in A and B at what distance will the shear be equal to ZERO between A and B what the computed maximum positive bending moment? Note: counterclockwise moment on the righthand side of the beam element be positive
A simple pin-connected truss is loaded and supported asshown in Figure P1.12. The load P is 200 kN. All members of thetruss are aluminum pipes that have an outside diameter of 115 mmand a wall thickness of 6 mm. Determine the normal stress in eachtruss member. Assume truss dimensions of a = 12.0 m, b = 7.5 m,and c = 6.0 m.
Calculate the shear stress at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading Pshown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (˚) =30 P (kN)=14
Is the another support force possible solve like this: r3*9m-4KN/m*2.5m*6.5m-12KN*1m=0 >r3= 8.56 KN
The rigid bars AC and BCD are supported by pins at A and B and by a steel rod at D. There is a roller connection between the bars at C. Compute the vertical displacement of point D caused by the loading. Cross-sectional area of rod is 250 mm² and E = 200 GPa.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of the neutral axis of the section in PART B in mm.0 Calculate the stress in the steel of the section in PART B in MPa.0 Calculate the ultimate moment capacity of the section in PART B in kN.m.0
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 3 Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal stress for the material is 0allow = 200 MPa 10 mm 40 mm a 60 mm- 10 mm 200 mm