The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque I that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze Steel C

The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque I that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze Steel C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 69 mm and G = 33.49 GPa. For the steel segment BC, the diameter is 49 mm and G = 83.14 GPa. Given that a = 2 m and b = 1.4 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 63.68 MPa in the bronze and 90.99 MPa in the steel. Round off the final answer to two decimal places.
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
The force P = 100 kN is applied to the bracket as shown in the figure. Compute the normal stresses developed at points A and B.
The pipe AB shown in the figure has an inner diameter of d = 86 mm and an outer diameter of D = 110 mm. Assume its end is tightened against the support at A using a torque wrench at B. [P = 100 N, D = 110 mm, d = 86 mm, b = 280 mm, a = 360 mm] Find the torque created by the force P. Find the second polar moment of area (J) for the cross-section of the pipe. Find the stress at the outer wall. Find the stress at the inner wall.
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
1) A uniform steel shaft has a diameter of 50 mm is fixed at ends A and B. The shear modulus of steel is 75 GPa.a) Write the equilibrium and compatibility equation(s) needed to solve the problem along with supporting sketches.b) Calculate the internal torques of each member in N-m.c) Using your solution from part (b), draw the internal torque diagram for the shaft using the rules we discussed in class.d) Calculate the maximum shear stress in the system in MPa. You will have to look at each individual piece of the system, so clearly indicate which segment has the maximum stress.[Ans. to check: τmax = 8.15 MPa]e) Calculate the total rotation of the shaft at point C in radians.
Two forces P1 and P2, of magnitude P1 = 15 kN and P2 = 18 kN, are applied as shown to the end A of bar AB, which is welded to a cylindrical member BD of radius c= 20 mm. Knowing that the distance from A to the axis of member BD is a= 50 mm and assuming that all stresses remain below the proportional limit of the material, determine the following: 1. What is the absolute value of the axial stress at point K of the transverse section of member BD located at a distance b = 60 mm from end B in MPa. 2. What is the flexural stress at point K of the transverse section of member BD located at a distance b = 60 mm from end Bin MPa. 3. What is the total normal stress at point K of the transverse section of member BD located at a distance b = 60 mm from end B in MPa.
Figure shows two views of the upper end of a bar B which is fastened to a fitting A by means of a pin of 5 cmdiameter. The force P = 32 kN. Determine:a. the shearing stress induced in the pin, Ans._____________b. the bearing stresses in A and B,Ans.____________c. the maximum tensile stresses in A and B.* note that the reaction at fittings A is equal and opposite to theapplied force at bar B. Ans.____________
The pipe shown, has an inner diameter of 80mm and an outer diameter of 100mm. If its end is tightened against the support at A using a torque wrench at B, determine the shear stress developed in the material at the inner and outer walls along the central portion of the pipe when the P (in newtons) forces are applied to wrench. P=74 Show detailed solution
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=66, T2 =11, T3 =26
The question is placed on picture. Please explain in detail. A cylindrical cantilever bar with diameter er 2 mm and length of 4 m subjected. Force F1 = 2KN is located at center and the force F2=5KN is located at bottom of the bar as it is shown in figure. Find maximum stress at point P.
For the cantilever beam shown in the figure, Find the: a)Support reactions b)Draw the shear and moment diagram c)Find the maximum bending stress in the rectangular wooden beam SHOW A COMPLETE AND ORGANIZED SOLUTION: