Problem 3 For the series/parallel pipe system shown, determine the total head loss in the system if the discharge in line 2 is 150 L/s. If the pressure at A is 400 KPa, what is the pressure at C? Diameters are in mm and pipe lengths in m.

Problem 3 For the series/parallel pipe system shown, determine the total head loss in the system if the discharge in line 2 is 150 L/s. If the pressure at A is 400 KPa, what is the pressure at C? Diameters are in mm and pipe lengths in m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 30 cm pipe is connected by a reducer to a 10 cm pipe. Points 1 and 2 are at the same elevation. The gage pressure at point 1 is 207 kPa gage. The flow rate from 1 to 2 is 30 L/s, and the head lost between 1 and 2 is equivalent to 2.5m. Find P2 if liquid is water.
Pipes 1,2, and 3 having diameter of 150mm. 200mm and 250mm and leading from reservoir A, B, and C respectively join at a common point. All pipes are new cast iron (C=120) and each is 500m. If the water level in reservoir A is 1.80m than that in B and 4.8m higher than that in C. a) Calculate the discharge in pipe 1.b) The head loss in pipe 2c) The discharge in pipe 3 ** Need asap pls. Thank you.
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
In the branched pipe system shown, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40 pipe at A. The flow splits into two DN 50 Schedule 40 pipes as shown and then rejoins at B. Calculate (a) the flow rate in each of the branches and (b) the pres- sure difference PA PB. Include the effect of the minor losses in the lower branch of the system. The total length of pipe in the lower branch is 60 m. The elbows are standard.
1. The figure shows a looping water pipe system. Pressure at A = 85 m and E = 55m. Assume f = 0.053 all pipes. a. Compute the discharge at pipe 1b. Compute the discharge at pipe 2c. Compute the discharge at point B
A main pipe distributing water has a diameter of 158 mm and is distributed into three outlets. Thefirst outlet has a velocity rate of 10m/s and a diameter of 50mm. The second outlet has a velocity rate of11m/s and a diameter of 75mm. The third outlet has a flow rate of 0.265619 m^3/s moving at avelocity of 15m/s. if the pressure head in the larger diameter part is 28 ft. a) determine thepressure head at the smaller diameter. b) what is the velocity head of the larger pipe? c) what is the velocityhead of the smaller pipe? d) What is the total head in the system?
A 1.20 m-diameter(internal)horizontal steel penstock conveys water at the rate of3.6 m3/s. The thickness of the pipe wall is 25 mm. Thebulk modulus of elasticity of water is 2.2 GPa. The pipehas length of 1000 m and the friction factor is 0.020. Thewater surface elevation in the reservoir is 60 m. If theflow is stopped completely by closing the valve in 2sec, determine the following:(a) the maximum water hammer pressure that candevelop.(b) the maximum pressure at the valve.(c) the elongation of the pipe in mm (△=ForcexL/AE) foran almost instantaneous closure.
The discharge from A to B is 50L/s. Pipe 1 is 650m long and 0.3m in diameter. Pipe2 is 500m long and 0.5m in diameter. Pipe 3 is 750m long and 0.4m in diameter. The surface roughnessin all pipes is 0.36mm. Assume that the kinematic viscosity of water is 1x10-6 m 2 /s. Determine the headloss from A to B. Solve using either the method of equivalent pipes or the Hardy Cross Method.
Using a standard pipe with a diameter of 0.1016 m and a length of 152.4 m, water at 16 ° C is transferred from a high tank (z1 = 213.5 m) to another tank (z2 = 200 m) at the lower level. Both tanks are open to the atmosphere. There are 1 closing slide and 2 90º standard elbows in the system. The friction factor is f = 0.01 and the correction coefficient can be taken as α = 1. Find the volumetric flow rate of water (m3 / s) (g = 9.81 m / s2; gc = 1 kg.m / N.s2).
Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
Three pipes of diameters 0.4m, 0.2m and 0.3m of lengths of 400m, 200m, and 300m, respectively, are connected in series. The compound pipe connects two water tanks having a difference of water level of 25m. Determine the discharge through the compound pipe neglecting the minor losses when the coefficient of friction for the compound pipe is 0.006.
A compound pipe consists of three pipes connected in series. The first pipe has a length of 115.3m, the diameter of 280mm, and Darcy-Weisbach friction factor f=0.0233. The second pipe has a length of 234.15m, the diameter of 230mm, and Manning's Roughness Coefficient n=0.0133. The third pipe has a length of 147.95m, the diameter of 250mm and a Hazen William coefficient C=110. If the pipe system carries a flow rate of 740 L/s: Determine the headloss in the first pipe in meters. Determine the headloss in the second pipe in meters. Determine the headloss in the third pipe in meters.