horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet.

Q: Question 4. The flowrate of the flow is 0,2c m'/s in a pipe placed on a horizontal plane. The pipe…

A: Given:- a = 4, b = 0,  c = 1  The flow rate of the flow = 0.2c m3/sec = 0.21 m3/sec The diameter of…

Q: Determine the pressure at the higher end if the pressure at the lower end is 24.525 N/cm^2. 23.924…

A:

Q: Q.2 (a) In a vertical pipe conveying oil of specific gravity 0.8, two pressure gauges have been…

A:

Q: The flowrate of water through the bend pipe (90o) is 0.21 m3/s. The pipe diameter at the inlet is…

A:

Q: The diameter of a pipe carrying water changes gradually from 150 mm at A to 450 mm at B. A is 5 m…

A: Given data,  Diameter at A = 150 mm Diameter at B = 450 mm Pressure at A = 70 Kpa Pressure at B = 50…

Q: A 50 mm diameter circular sharp-edged orifice at the side of a tank discharges water under a head of…

A: Given: The diameter of the orifice is 50 mm. The head is 3 m. The coefficient of contraction Cc is…

Q: A 10-cm diameter x 20 m long closed conduit pipe inclining at 45°, flowing upward full of water at a…

A: Given, D = 10 cm or 0.1 m L = 20 m  P1 = 50 kPa f = 0.02

Q: Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter), then along BC (3 m long,…

A: The Bernoulli Equation is the method of the preservation of energy principle appropriate for flowing…

Q: 2)Pipe A,600mm in diameter and 3000m long draws water from reservoir "A" with water surface…

A: As per the given information we have to calculate the required unknown.  The discharge through pipe…

Q: Compute the pressure at point B

A:

Q: The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the…

A:

Q: A 20-hp suction pump at 70% efficiency draws water from a suction line whose diameter is 200mm and…

A:

Q: Assume frictionless flow in a long, horizontal, conical pipe, which has a diameter of 3.6 ft at…

A: Given: The entrance diameter of the pipe is 3.6 ft. The exit diameter of the pipe is 2.4 ft. The…

Q: Assume frictionless flow in a long, horizontal, conical pipe, where the diameter is 3.6ft at…

A:

Q: Water at 65 degrees Celsius is flowing horizontally at a rate of 84.1 m^3/hr in a pipe. It enters a…

A: Answer We can determine the magnitude and direction of the force by using the equation of motion.…

Q: 0.5 m B 30 mm 5 m 8 m/s 50 mm 3 m mm

A: Given Data: Water flows into the Tee at 8 m/sec. It flows under a pressure of 40 kPa. Velocity of…

Q: Assume frictionless flow in a long, horizontal, conical pipe, where the diameter is 1.6m at entrance…

A: Given: The entrance diameter is 1.6 m. The exit diameter is 1 m. The pressure at the smaller end is…

Q: m³ 3 S Water flows at a rate of 0.035 in a horizontal pipe whose diameter is reduced from 15cm to…

A:

Q: 14 A cylindrical vessel closed at the top and bottom is 300mm inn diameter, 1m long and contains…

A:

Q: Water flows through a large size pipe with total and static pressure head of 0.5m and 0.3m of fluid.…

A:

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: Given,

Q: A 500 mm diameter pipe carries water at L/s. A pump in the pipe is used to move the water from point…

A: d (diameter of pipe) = 500mm = 0.5m Q (discharge) = 500L/s = 0.5m3/s

Q: Q-2 Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

A: It is required to find the velocity of flow at minimum area section.

Q: Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a…

A: Introduction- The energy expended in a fluid system due to friction throughout the length of a pipe…

Q: Flowrate of water through bend pipe (90°) is 0.21 m3/s. The pipe diameter at the inlet is 150 mm and…

A: The discharge is Q=0.21 m3/s. Consider the following figure. Calculate the velocity at the inlet as…

Q: b) A horizontal pipe of 150 mm diameter for the initial 30 m and 75 mm diameter for the remaining 10…

A:

Q: Calculate the total hydrostatic force and the location of the center of pressure (yp) acting on the…

A:

Q: Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 896.61 L/min from…

A: Given data  Height of liquid  Discharge  Outer diameter  Pipe roughness Temperature  Kinematic…

Q: A vertical conical pipe has diameter 1.5 ft at the top and 3.0 ft at the bottom and 60 ft long. The…

A:

Q: Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 895.55 L/min from…

A: Calculate the velocity of flow as follows. v=QA=895.55×10-360×6.793×10-3=2.2 m/s Calculate Reynold's…

Q: Water enters the pump of a steam power plant at 20 kPa and 50 °C (p = 988 kg/m', & Pr = 12.352 kPa)…

A:

Q: Water flows through a horizontal pipe with a cross-sectional area of 5m^2 at a speed of 6L/sec. With…

A:

Q: Water flows as two free jets from the tee attached to the pipe as shown in Figure Q2. The exit speed…

A: As per our company guidelines we are supposed to answer only first 3️⃣ sub-parts. Kindly repost…

Q: Compute the depth of the center of pressure for a vertical circular gate having a diameter "h" when…

A: Using centre of pressure formula

Q: Q: In a rough pipe of diameter 500mm and length 3500m, water is flowing at the rate of 0.5 m/s. If…

A:

Q: 0.001kg 1. Water (µ = -)is flowing through a 3-mm diameter, 9-m long horizontal pipe steadily at…

A:

Q: Water flows at a rate of 0.035 m3 /s in a horizontal pipe whose diameter is reduced from 15 cm to 8…

A:

Q: Q-2 Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

A:

Q: Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 896.61 L/min from…

A: Above given data we have to find PB

Q: a duct as shown. The inlet water velocity is Vertical 10 m/s. The cross-sectional area of the duct…

A: step 1-

Q: 4.96 Water is discharged at a flow rate of 0.3 m³/s from a narrow slot in a 200-mm-diameter pipe.…

A: Given: Discharge, Q=0.3 mDiameter, D=200 mmThickness, t=20 mm

Q: Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If…

A:

Q: A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which…

A: The head, pressure, or power (are the same) is lost through running water in a pipe or station. Due…

Q: Q: In a rough pipe of diameter 500mm and length 3500m, water is flowing at the rate of 0.5 m'/s. If…

A:

Q: A closed cylindrical tank 2m in diameter and 7m high has 3m tall of water and 3m of oil (SG = 0.8).…

A:

Q: Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross sectio pipe as shown in Figure…

A: given l= 70m temp of air =30'c velocity = 2m/s

Q: If the friction headloss is significantly changing in a pipe flow, which of the following is most…

A: Given data in question  Pipe flow Friction head loss To be discussed  Friction headloss…

Q: A vertical pipe 3 ft in diameter and 30 ft long has a pressure head at the upper end of 22 ft. of…

A:

Friction

Friction is defined as the force that prevents any solid surface, any layer of fluid, or any kind of element or material from sliding.