Problem 3. The truss is shown below. a. Sketch the influence lines for the support reaction at E, members FB, FG and FC. a. If the truss is loaded with uniform dead load 25 kN/m, uniform moving load of 42 kN/m and a concentrated live load of 9 kN, determine the maximum axial forces of the following: support reaction at E, members FB, FG and FC? B 4 at 8.0m D A 1.75 m 4.25 m

Problem 3. The truss is shown below. a. Sketch the influence lines for the support reaction at E, members FB, FG and FC. a. If the truss is loaded with uniform dead load 25 kN/m, uniform moving load of 42 kN/m and a concentrated live load of 9 kN, determine the maximum axial forces of the following: support reaction at E, members FB, FG and FC? B 4 at 8.0m D A 1.75 m 4.25 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 2P

See similar textbooks

Related questions

Q: 6. Design a circular sedimentation tank with a retention period of two hours for a town with a…

Q: A 252 km² catchment area has a 6 hr UH which is a triangle with time base of 35 hours. What is the…

Q: Learning Goal: To learn to apply the method of joints to a truss in a systematic way and thereby…

Q: The beam shown below is subjected to a varying distributed loading, a couple, and a concentrated…

Q: (b) A simple reservoir has a linear storage indication curve defined by Q/2 = S/At, where At = 1.0…

A: Given, Q/2 = S /Δt, where Δt = 1.0 h S at 8 A.M=0 ft3 /s-hr To determine, Route the hydrograph

Q: 2. 7777 6000 N/m 4 4m t NOS 2m / 2m 4m 9000 N/m +

Q: Q- A simply supported rectangular beam having span 5m is subjected to a central point load of 50 kN.…

A: Given- Span=5 m load=50 kN Stress=220 N/mm2,

Q: The whole circle bearings of line OA and OB are 18°15' and 335°45' respectively. What is the value…

A: Given data: The whole circle bearings of line OA and OB are 18°15' and 335°45' respectively.…

Q: A soil has dry unit weight of 18 kN/m², specific gravity of 2.65 and degree of saturation of 72%.…

Q: what kind of elements are considered to develop equipment for the vibro comaction and vibro…

A: This question is related to the Soil Mechanics from Civil Engineering. This question is subjected to…

Q: fluid is flowing An incompressible homogenous steadily in a variable diameter pipe having the large…

A: Given data. Variable diameter of an incompressible homogeneous fluid flowing in pipe is, DA=15…

Q: Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000…

A: a ) P = 9000 lb and F = 3000 lb Compute the stresses at A and B ? Solid mechanics problem.

Q: 4/ The following is an incomplete page of level book in which X indicates missing Entry line.…

A: Using rise and fall method

Q: For the cross section shown below, y 1 4a 1 8a I 8a 4a |4ª| 10a 28a 8a ба Dimensions in millimeters…

Q: For the truss shown in the figure, the force in the member QR is

Q: How Lights Play an Important Role in Interior Design and Kitchen Designs for Small Space?

A: Lighting is one of the most important elements of interior design for commercial space. it helps…

Q: A rolled steel beam section ISHB 150 @ 265.85 N/m is used as a stanchion and has an unsupported…

A: Given- Rolled steel beam section ISHB 150 @ 265.85 N/m, Unsupported length = 4.5 m, Yield stress for…

Q: A continuous concrete beam shown in the figure has a width of b= 300 mm, an effective depth of d=…

A: A continuous concrete beam shown in the figure carries A dead load at Span AB of 7.5 kN/m Span BC,…

Q: 3. Determine all reactions at the wall and at A, and the equations of the elastic curve in terms of…

Q: A closed cylindrical tank, 1.5m in diameter and 3m high contain 2m of water & air space with a…

Q: what kind of elements are considered to develop equipment for the vibro comaction and vibro…

A: Given data- Brief concept introduction- Vibro compaction- Vibro Compaction is a ground improvement…

Q: The bracket is supported by 1/2 inch diameter pins at A and B (the pin at B fits in the 45° slot in…

Q: An I-section beam ABC has a constant El and is loaded as shown in the figure below. This beam has a…

A: Given: Required: Constant of integration C1 and C2 Moment reaction at C Vertical force reaction at…

Q: A PL15X125 is connected to a gusset plate with 4 M22 bolts. Determine the allowable and design…

A: Answer We are given PL 15 x 125 Number of bolts = 4 M 22 bolts A 36 steel Calculation shown in…

Q: Problem 1. The beam is shown below. Draw the influence lines using Brute-Force Method for the…

A: When unit load at A, ∑ME=0-RD×3.25=0RD=0∑MA=0-RC×5-0×10.75=0RC=0∑V=0RA+RC+RD=1RA+0+0=1RA=1Shear at…

Q: A closed tank containing water is partly filled with water and the air space above it is under…

A: Given- Diameter of the bore=5 cm, Friction loss=1.5 m of water, Discharge Q=15 L/s, Density of…

Q: 3.00 3.00 300 kNm 6.00 P=229kN 90 kN/m 7.00 -12.0 m 4.00 6.00 For the beam loaded as shown,…

Q: 2. Find the forces acting in members U₁U₂, LoU₁ and LoL₁. Use the method of sections. 60 k- 40 k 40…

Q: Problem 1 Using the slope-deflection equations, compute the moment and vertical reactions at…

Q: 14. Si la diferencia en el nivel de mercurio dentro del manómetro es de 80 mm, determine el flujo…

A: Concept To get the volumetric flow, We will use equation of Bernoulli's,which is solve in solution…

Q: لبيتين 2m A ھ 11 kN 29 N/m Using SLOPE DEFLECTION METHOD, compute the slope and deflection at B. 8m…

A: Taking trapezoidal load intensity of 7 KN/m at point C as length of trapezoidal load is not…

Q: For the beam shown in Fig.1 (let E = 210 GPa and I = 4 x 10-4 m4 throughout the beam length): Node…

A: Given : A cantilever beam with loading on it Required: Displacement curve, slope, shear force and…

Q: A submerged stratum of clay has a thickness of 15m. The average water content of samples taken from…

A: Given, w = 54% G = 2.78 Thickness = 15 m

Q: El aire a una temperatura de 80°C fluye a través del tubo. En A, la presión es de 20 kPa y la…

A: We are given Air at a temperature of 80oC flows through the tube. In A, the pressure is 20 Kpa and…

Q: Problem 9.4 - Draw the shear (V) and bending moment (M) diagrams for the beam below. Aurum A 8 kN.m…

Q: Determine the largest tensile and compressive forces that occur in the members of the truss and…

A: Given: Largest Tensile and compressive force and its members have to be determined under two cases.…

Q: Consider a homogenous plate made up of a semi-ellipse and a rectangle whose base is of length 2b,…

A: Given: A plane area made up of semi-ellipse and a rectangle. Length of rectangleL=2b To find:…

Q: what kind of elements are considered to develop equipment for the vibro comaction and vibro…

Q: 2 kN/m 5 m 3 m 10 kN -2m- Draw the shear diagram for the beam Draw the moment diagram for the beam B

A: Given, Load = 10 kN UDL = 2 kN/m Span of simply supported beam = 10 m

Q: A bed of sand consists of three horizontal layers of equal thickness. The value of k for the upper…

Q: If a vertical curve's incoming grade (g₁) is -5%, the outgoing grade (g₂) is 5%, the station at the…

A: Given, g1 = -5% g2 = 5% L = 3000 ft PVI = 25+00 PVI (El) = 450 ft

Q: explain what is waste hierarchy?

Q: Determine the reactions

Q: 2 kN A -2 m 1.5 kN/m 2 m B 00

A: A cantilever beam free at A and fixed at B, is loaded with a point load of 2 kN at the free end and…

Q: A nozzle is so shaped that the average flow velocity changes linearly from 1.5 m/s at the beginning…

A: Given- flow velocity change from 1.5 m/s to 15 m/s, distance=0.375 m

Q: pleaseee

Q: A singly reinforced rectangular concrete beam having depth of 450 mm and width of 250 mm. Effective…

Q: Project closeout is the final construction phase of the project lifecycle. This phase occurs after…

A: Project closeout is the final construction phase of the project lifecycle. This phase occurs after…

Q: Infiltration capacity of a soil is defined as The maximum rate of infiltration into the soil…

A: Using definition of infiltration capacity

Q: 12.8 Given five-story building, that weighs a 100kips and has concrete shear walls and special…

A: Data given Weight, W = 100 kips Accelerations SDS = 1.1 SD1 = 0.6 Building…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Express your intermediate answers with at least FOUR decimal places and simplify your FINAL answers up to TWO DECIMAL PLACES. BOX your FINAL ANSWERS

Problem 3. The truss is shown below.
a. Sketch the influence lines for the support reaction at E, members FB, FG and FC.
a.
If the truss is loaded with uniform dead load 25 kN/m, uniform moving load of 42 kN/m and a
concentrated live load of 9 kN, determine the maximum axial forces of the following: support
reaction at E, members FB, FG and FC?
B
4 at 8.0m
D
A
1.75 m
4.25 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step by step

Solved in 10 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw the Influence Line Diagram of members HI, KL, IJ, BI, FK, CD, and EF.Determine the maximum axial tension or compressive force to this members when a moving load of 75 KN and 50 KN (2 meters apart) is at member BH (Dead Load = 6 kn/m, Live Load = 10 kn/m).
1. Draw the influence line for the vertical reaction at internal hinge C. 2. Determine the length and position of a 10kN/m uniformly distributed load that will give a maximum positive shear at C. 3. What is the moment at point D when the previous scenario happens? 4. Determine the maximum moment at D and its location when a 12kN load travels across the beam.
Draw the influence lines for bar forces in mem- bers HD and HC of the truss shown in Figure P12.33. The load moves along the bottom chord of the truss. If the truss is to be designed for a uniform live load of 0.32 kip/ft that can be placed anywhere on the span in addition to a concentrated live load of 13 kips that can be positioned where it will produce the largest force, compute the maxi- mum tension and compression forces in bar HD.
~#Draw the influence lines for members DI and IJ of the truss depicted in the figure below assuming that the loads are being transmitted to the bottom chord. Determine the following member forces while also taking into account the 3-point moving load as illustrated. Assume that the loads only move in the right direction.#~ a. Maximum tension on member DK in kN. b. Maximum compression on member DK in kN. c. Maximum tension on member CI in kN. d. Maximum compression on member CI in kN.
The horizontal load P can act at any location along the length of member AC shown in Figure P12.26. Draw the influence lines for the moment and shear at section 1, and the moment at section 2.
A uniform live load of 3 kN/m and a single live concentrated force of 45 kN can be placed on the haunched girder. Illustrate the Influence Line and determine the maximum live negative moment at B.
A uniform live load of 3 kN/m and a single live concentrated force of 45 kN can be placed on the haunched girder. Illustrate the Influence Line and determine the maximum live positive shear at B.
Determine the following: 1. Maximum positive (upward) reaction at B2. Maximum positive moment at C3.Maximum negative shear at C
Determine the support reactions at A and B if the frame is loaded by a horizontal concentrated load 133.5 kN at D, a 96 kN downward concentrated load at C and a 256 kN.m clockwise moment at C. Determine the reactions at supports A and B.
The multi-span girder has two shear plate connections that act as hinges at C and D. The midspan girder CD is simply supported on the cantilevered ends of the left and right girders. Determine the forces in the hinges and the reactions at supports A, B, E, and F. Also draw the shear and moment diagram.?=70 kN/m ?1=10 m ?2=2.5 m ?3=6 m ?4=1.5 m
For the beam shown, determine the reaction at the roller support when w0 = 6 kips/ft.
Given : M1 = 400 kN-m M2 = 500 kN-m M3 = 600 kN-m P = 150 kN w1= 60 kN-m w2 = 120 kN/m a = b = d = 6 m c = 4 m Determine the following: a. The maximum positive shear (in kN). b. The maximum negative shear (in kN). c. The maximum positive moment (in kN-m). d. The maximum negative moment (in kN-m). e. The location of maximum shear from the left end of the beam (in m). f. The location of the maximum moment from the left end of the beam (in m). Kindly Draw the Shear and Moment Diagram. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.