Problem 4: A WF section has a simple span of 12 m. The beam is laterally supported at both ends and at the midspan. It carries a service uniform dead load of 12 kN/m. 1. Determine the flexural strength of the beam. 2. Determine the safe service concentrated live load that the beam could support at its midspan.

Problem 4: A WF section has a simple span of 12 m. The beam is laterally supported at both ends and at the midspan. It carries a service uniform dead load of 12 kN/m. 1. Determine the flexural strength of the beam. 2. Determine the safe service concentrated live load that the beam could support at its midspan.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The inverted T section of 6 m overhang bearn has the properties shown. The beam carries a uniformly distributed load W_{0} over its entire length and a concentrated load of 5 KN, 3 m from the rightmost support. Determine W_{0} if f b(T) =30 MPa and f b(C) =70 MPa
A cantilever beam, 6m long, fixed at point A and free at point B, is subjected to a downward uniform load 50 kN/m throughout the beam. a. Determine the slope of A wrt B. b. Determine the slope of B wrt A.
An L = 38-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from wA = 430 lb/ft to wC = 270 lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 5000 lb on the soldier beam at a = 29 ft. Determine the horizontal deflection of the soldier beam at point C. Assume EI = 3.8 × 108 lb·in.2. Deflection is positive to the left.
A triangular wooden beam width 150 mm base and 300 mm height carries two concentrated load of 20 kN at third points. If the simple span of the beam is 6 m. Compute the maximum shearing stress of the beam. a. 0.58 MPa b. 1.33 MPa c. 0.48 MPa d. 0.86 MPa
An L = 23-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from wA = 410 lb/ft to wC = 290 lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 4500 lb on the soldier beam at a = 18 ft. Determine the horizontal deflection of the soldier beam at point C. Assume EI = 6.4 × 108 lb·in.2. Deflection is positive to the left.Answer:vC = Type your answer here in.
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the maximum shear of the beam in KN? What is the maximum moment of the beam in KN.m?
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ, compression bars As’ = 2-28 mmØ, d’ = 60 mm. Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa. a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN
strength of materials A built-up steel I-girder is 2 m deep over the flanges, each of which consists of four 1 cm plates, 1 m wide, riveted together. The web is 1 cm thick and is attached to the flanges by four 9 cm by 9 cm by 1 cm angle sections. The girder has a clear run of 30 m between the supports and carries a superimposed load of 60 kN per metre. Find the maximum longitudinal stress. (Cambridge)
A 5-m propped beam carries a uniformly distributed load equal to 45 kN/m applied throughout the beam. If the reaction at the roller is 84.375 kN, what is the maximum flexural shear stress if the beam has a rectangular cross-section with b = 300 mm and h = 600 mm? (in MPa)
A steel beam having a simple span of 8 m. is subjected to a clockwise moment M at the left end and 25% of M (counter clockwise) at the right end. The steel section has the following properties. Fy = 248 MPa rt = 0.053 m d = 0.533 m bf = 0.210 m tf = 0.016 m Sx = 0.00206 m^3 1. Compute for the maximum slenderness ratio of the beam which is considered as long beam. 2. Compute the allowable bending stress in the compression flange. 3. Compute for the value of the moment at the left end.
A prismatic beam having 250 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ20 mm with an effective depth of 420 mm. It is simply supported over a clear span of 6 m and designed to support a total factored uniformly distributed load of 32 kN/m over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. 1. Determine the factored shear force at the critical section, distance "d" from the face of support . (A to D) 2. Determine the nominal concrete shear strenght in kN as per NSCP 2015. (E to H) 3. Determine the required spacing in mm of 10-mm-dia. stirrups within the critical region of the beam. (I to L) Correct Answers: A. 82.5 F. 80.2 I. 200