Problem 4: from the figure, calculate, (a.) maximum normal stress in the Horton sphere diameter 60 – ft. and wall thickness of 1.13 in. with welded joints by a gas at pressure of 75 psi (Ib per square inch), (b.) the force transmitted by the internal pressure to a 10 – in. length of the vertical meridian joint of the shell.

Problem 4: from the figure, calculate, (a.) maximum normal stress in the Horton sphere diameter 60 – ft. and wall thickness of 1.13 in. with welded joints by a gas at pressure of 75 psi (Ib per square inch), (b.) the force transmitted by the internal pressure to a 10 – in. length of the vertical meridian joint of the shell.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.12P: Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft....

See similar textbooks

Similar questions

A closed cylindrical tank containing a pressurized fluid has an outside diameter of 448 mm and a wall thickness of 11 mm. The tank is pressurized to 2.53 MPa. Determine the hoop stress in the wall of the tank. Round off the final answer to five decimal places.
A thick cylinder 1 meter inside diameter and 7m long is subjectedto an internal fluid pressure of 40MPa. Determine the thickness of the cylinder ifthe maximum shear stress in the cylinder is not to exceed 65MPa. What will be theincrease in the volume of the cylinder? E=200GPa, μ= 0.30.
Determine the normal stress in a ball, which has an outside diameter of 165 mm and a wall thickness of 3.4 mm, when the ball is inflated to a gauge pressure of 81 kPa.
SHOW COMPLETE SOLUTION AND SKETCH THE ILLUSTRATION A cylindrical tank 6.7 m in diameter is made from steel plates that are 12 mm thick. Find the maximum height to which the tank may be filled with wine with density 720 kg/m3 if the circumferential stress is limited to 41.4 MPa.
A typical stainless steel cylindrical vessel is shown. The outside diameter of the tank is 47.9 in. and the wall thickness is 0.58 in. The tank is pressurized to 1.36 ksi. Determine the longitudinal stress (in psi) in the wall of the tank . Round off the final answer to five decimal places.
The wall thickness of a 4-ft-diameter spherical tank is 5/6 inch. Calculate the allowable internal pressure if the stress is limited to 8000 psi.
For the two-dimensional flow system shown below (units in meters): Express how you will calculate the total vertical stress (do not compute it).
referring to the figure below, calculate the distribution of vertical stress along vertical plane passing through one of the two forces. Specify the value of stress in kPa at depth of 4m
calculate the total stress, pore water pressure, and effective stress at points A, B and C.
The wall thickness of a 3-ft diameter spherical tank is 3/4 in. Calculate the allowable internal pressure if the stress is limited to 7 ksi. CHOISES ARE: 583.333 psi 156.25 psi 208.333 psi 222.222 psi 300 psi 243.056 psi 166.667 psi
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. To what value could the internal pressure be increased/decreased if the allowable design stress is 120 MPa?
A newtonian fluid flows down an infinitely long cyalindrical tube (as shown in the figure below). There is NO applied pressure gradient, and fluid flows down the pipe due to gravity alone.i) Derive the velocity profile (?(?) =?). ii)Find???? ,???iii) Draw the velocity and shear stress profiles, showing the points where ? or ? is equal to zero or at their maximum value.