Problem 4: Inputs: ● ● ● ● ● L₁ = 13 in L₂ = 11 in h = 10 in F = 40 lb 0 35° (measured from vertical) There is a pin at A and roller at B. h F L₁ L₂ a) Compute the horizontal component of the reaction at A. Indicate direction with your boxed answer. b) Compute the vertical reaction at A. Indicate direction. c) Compute the reaction at B. Indicate direction. B

Problem 4: Inputs: ● ● ● ● ● L₁ = 13 in L₂ = 11 in h = 10 in F = 40 lb 0 35° (measured from vertical) There is a pin at A and roller at B. h F L₁ L₂ a) Compute the horizontal component of the reaction at A. Indicate direction with your boxed answer. b) Compute the vertical reaction at A. Indicate direction. c) Compute the reaction at B. Indicate direction. B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
Calculate the reaction forces on the bearing near the pulley and bearing at the far end of the shaft. Include a free body diagram and coordinates. Given the shaft length is 1 meter= Mass=40Kg Static load = 8600N Dynamic (running load) = 8400N Some hints:1. This solution will require you to draw known forces and find unknown reactions in 2perpendicular planes and then add the horizontal and vertical reaction forces asvectors to find the reaction force (hypotenuse).2. Bearings are usually mounted as near as possible to the ends of the shaft withoutfouling the other machine elements. The bearing at the far shaft end can be mountedat the 1 meter point. The bearing at the pulley end should allow clearance to assemblethe pulley.3. Bearing reaction forces are typically simplified as a single point load through thebearing centre.
Figure Q2 shows an arrangement used to transfer materials F to a construction site. The rod OB is fixed at datum O. One of the systems used have dimension and loads as given in Table Q2. During operation, Pulley A is rotated as shown to move the load upwards. The inclination angle of rod OB is θ = 45O. Determine: Stress in Rope 1 (in MPa) Stress in Rope 2 (in MPa) Extension in Rope 2 (in mm) The minimum diameter of Rope 2 (in mm) if the stress is at yield
For problem on the picture. assume that the left side of the spring has a fixed end and the other side has pull force applied to it. The force applied to the spring is 3lbf. Solve for the following:a. Draw the free body diagram using the equivalent spring constantb. total deformation of the spring
Problem 4
The frame in (Figure 1) supports the 350lb load. The pulley at C has a radius of 0.5 ft. The pulley at D has a radius of 0.25 ft. a) Determine the reaction at pin A. b) Determine the reaction at pin B.
A countershaft carrying two V-belt pulley is shown in Figure 1. Pulley A receivespower from a motor through a belt with the belt tensions shown. The power is transmittedthrough the shaft and delivered to the belt on Pulley B. Assume the belt tension on the loose sideat B is 15 percent of the tension on the tight side.(a) Determine the tensions in the belt on pulley B (assuming the shaft is running at a constantspeed).(b) Find the magnitudes of the bearing reaction forces assuming the bearings act as simplesupports.(c) Draw the shear force and bending moment diagrams for the shaft.
Solve the reaction forces.
Draw the shear and bending moment diagrams and determine Vmax and Mmax. (remember to find support reactions)
The squared and grounded ends of a safety valve with 7.5 coils. The coils measure 105 mm in diameter on the outside and 17 mm wire diameter. It measures 210 mm in free length. 82 Gpa is the modulus of rigidity. Calculate the initial compression length of the wire required to maintain a boiler pressure of 1.35 Mpa on a 30 mm diameter valve seat. (Draw the diagram)
A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side. Determine the tensions in the belt on pulley B, assuming the shaft is running at a constant speed. Find the magnitudes of the bearing reaction forces, assuming the bearings act as simple supports. Draw shear-force and bending-moment diagrams for the shaft. If needed, make one set for the horizontal plane and another set for the vertical plane. At the point of maximum bending moment, determine the bending stress and the torsional shear stress. At the point of maximum bending moment, determine the principal stresses and the maximum shear stress.
PROBLEM: 4 A helical spring is made from a wire of 11 mm diameter and is of outside diameter 101 mm. The spring has 8 numbers of active coils. If the permissible stress in shear is 480 N/mm2 and the modulus of rigidity is 87 KN/mm2. Find the axial load which the spring can take and the deflection produced.