Problem #4: P B C Blocks A, B, and C have weights of Y N, 25 N, and 15 N, respectively. The coefficient of static friction between A and B is 0.3, between B and C, 0.4, and between block C and the ground, 0.35 13. Determine the smallest force P that will causes impending motion. 14. Determine the friction force between A and B 15. Determine the friction force between B and c

Problem #4: P B C Blocks A, B, and C have weights of Y N, 25 N, and 15 N, respectively. The coefficient of static friction between A and B is 0.3, between B and C, 0.4, and between block C and the ground, 0.35 13. Determine the smallest force P that will causes impending motion. 14. Determine the friction force between A and B 15. Determine the friction force between B and c

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Describe the Position of lateral pressure resultant for stability analysis.
The concrete gravity dam given in the figure has a width B=150 m (into the paper) 1. Calculate the hydrostatic force on the dam. 2. Assuming that the uplift force is 20% of the dam weight and that the static friction is 0.65 (between the dam and the soil), prove the the dam is table against sliding and against overturning around the point O.
A rectangular gravity dam has a height of 5 m. it retains water 4.2 m deep. Calculate the minimum width of the concrete dam that is necessary to prevent the dam from sliding. The specific gravity of the concrete is 2.4 and the coefficient of friction between the base of the dam and foundation is 0.5. Use factor of safety against sliding of 1.5. a. 2.556 m b. 1.963 m c. 2.292 m d. 2.205 m
A cylinder weighing 400 lb is held against a smooth incline by means of the weightless rod AB in FIig. P-309. Determine the forces P and N exerted on the cylinder by the rod and the incline respectively.
The two forces of magnitude F = 24 kN form a couple. Determine the corresponding couple-vector 1 answer below »
A dam rectangular in cross – section with upstream face vertical. Water is 20.4 m deep on the upstream side. The dam is 23.2 m high and 14.8 m wide at the base and weighs 2310 kg/m3. Coefficient of friction between the base and the foundation is 0.85. Compute the factor of safety against sliding. a. 3.85 b. 2.67 c. 3.24 d. 1.45
A block weighing 100 N is placed on an inclined plane of slope angle 30 degrees and is connected to a secondhanging block of weight “W”, by a cord passing over a small frictionless pulley. The coefficient of slidingfriction is 0.3. Find the weight “W” for which the 100N block moves up the inclined plane at a constantvelocity.
A vertical triangular plate whose height is 3.6 meters has its base horizontal and vertex upper most in the water surface. a. Find the depth to which it must be lowered from its vertex so that the difference in level between the center of gravity and the center of pressure shall be 20cm. b. How far is the center of pressure below the water surface? c.What is the base width of the plate if the total hydrostatic force acting on the plate is 76.28 kN?
A concrete dam retaining water is shown in FIGURE FMHF-1. If the specific weight of concrete is 23.5 kN/m^3, determine the following: Factor of safety against sliding (coefficient of friction: 0.48)a. 2.48 b. 1.34 c. 3.77 d. 3.42 39. Factor of safety against overturninga. 1.34 b. 3.105 c. 3.416 d. 1.987 40. Maximum soil pressure intensitya. 73.22 b. 183.48 c. 173.53 d. 58.48
A rectangular dam that is 4 meter wide and 10 meter high retains 8 meter high seawater with specific gravity equal to 1.05 . Determine the factor of safety for sliding and overturning per linear meter if the coefficient of friction between the dam and the sea floor is 0.8 and unit weight of concrete is 23.5kN/m^3.
Calculate the super elevation ё for a railroad track having a rail guage of 1560 mm for a 600 meter radius curve at a rated speed of 80 kph. (Answer should be in mm).What is the flange pressure F exerted on the wheels of 46,000 kg car coach traveling the curve at a maximum velocity of 120 kph? (Answer should be in kN).
A sliding gate 3m wide by 1.60 m high is in a vertical position. The coefficient of friction between the gate and guides is 0.20. If the gate weigh 18 kn and its upper edge is 10 m below the water surface, what vertical force is required to lift it? Neglect the thickness of the gate.