Problem 4.2. The two plates of wood (shown in the figure) are fastened by three 20 mm diameter bolts. The width and the thickness of the plates are 130 mm and 25 mm, respectively, and Pis 50 kN. Assuming Pis distributed equally among the three bolts, determine: 1- The shear stress in each bolt. 2- The bearing stress in each plate. 3- The maximum average tensile stress in each plate.

Problem 4.2. The two plates of wood (shown in the figure) are fastened by three 20 mm diameter bolts. The width and the thickness of the plates are 130 mm and 25 mm, respectively, and Pis 50 kN. Assuming Pis distributed equally among the three bolts, determine: 1- The shear stress in each bolt. 2- The bearing stress in each plate. 3- The maximum average tensile stress in each plate.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The figure below are timber planks joined together by a bolt with the corresponding measurements. Find the maximum safest P if the working stresses of the planks are 77 ksi and 68 ksi for tension and bearing respectively.
For the wooden beam sketched in the figure, ask for the mid-span section. a) Determine the normal stresses at points 1, 2, 3 and 4. (Represent the distribution of normal stresses in the section) b) Check the structural safety in relation to normal stresses. (Adopting γt = 3.2 and γc = 2.5) ADDITIONAL DATA / INFORMATION Characteristic strengths of wood: TENSION: σr,t = 52 MPa COMPRESSION: σr,c = 40 MPa
In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 60000psi. If the working compressive stress for the wood is 216psi. Determine the smallest permissible diameter of the pole.___________inches in 2 decimal places. Take note: Write it on a paper, hand written showing answer. Thanks
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
. Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in'the two materials must not exceed 50 MN/m 2 and 100 MN/m z respectively. [27.6, 19.5, 19.5, 13.8 ram.] Can you please show a full solution explaining what * means if you are using it thanks
Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane ofthe joint and the faces of the boards must be between 10° and 40°. Under a tensile load P, the normal stress in the boards is 4.9 MPa.(a) What are the normal and shear stresses acting on the glued joint if α = 20°?(b) If the allowable shear stress on the joint is 2.25 MPa, what is the largest permissible value of the angle a?(c) For what angle a will the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
rectangular steel plate, 1·2 m long and 850 mm wide, is subject to a compressive load along its length. If the width of the plate increases by 0·09 mm under load, determine its change in length. Take Poisson’s ratio for the steel as 0·28
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
Give the complete formula with all the variables to find the modulus of elasticty when velocity, unit weight and possion's ratio is given.
A 5 ft. long laminated wood beam is built up by gluing together three 2” x 6” boards to form asolid beam 6” x 6” cross section, as shown in the figure. Calculate the maximum allowable valueof P (lb.) such that both the (1) allowable shear stress in the glued joints of 100 psi and the (2)allowable bending stress of 1200 psi is not exceeded. (Disregard the weight of the beam).[Formula: Bending Stress:  = (M)(y)/I; max = (M)(c)/I; Transverse Shear Stress:  =(V)(Q)/(I*t); max = (V)(QNA)/(I*tNA)]
The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls. At a temperature of –20°C, there is a gap of 2.2 mm, as shown below. Determine the temperature in °F at which the compressive stress in the bar will be 30 MPa. Use α =18(10)-6/°C and E = 80 GPa. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
A joint is made by gluing two plywood gussets of thickness t = 0.56 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.65 in and the applied force is P = 7475 lb. Round off the final answer to three decimal places.