Problem 520kN.Two couple forces (20kN and F) act onthe beam.1. Find the magnitude of F so that theresultant couple moment is 50kN.m.clockwise.F1.5m0.75m-F2. Find the resultant couple force.3. Find the distance between the resultantcouple force.20kN

For a step-by-step solution have a look through the attached pictures of the solution. The required…

Answered: Problem 5 20kN Two couple forces (20kN…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.6P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Similar questions

with the following modifications: Replace the vertical 6kN at point B with a horizontal force 6kN acting to the right at the same point.
A 30N pair of forces equivalent to these pairs will be placed at points A and B. So what should the AB length be?
Expiremental Method: Force Table F1 - 150N, 30° N of E F2 - 100N, 60° E of S 1) Find the Equilibrant Magnitude and Equilibrant Direction 2) Find Resultant Force Vector Magnitude and %Error 3) Find Resultant Force Vector Direction and %Error
Distributed load, w0 = 4 N/mL = 3.4 m Find the following: Find the magnitude of the equivalent concentrated force (in N). Find the distance of the equivalent concentrated force from A (in m).
Find the magnitude (in Nm) of the couple moment acting on the pipe assembly if P = 159 kN. Round off only on final answer expressed in 3 decimal places.
Find the unknown forces
A ball (B) is stopped on inclined surface 30° with horizontal by a horizontal force p=100N. a. Resolve the force P in two rectangular components parallel and normal to the inclined surface. b. If another force T=50 N pull the ball in direction parallel to the inclined surface , replace this pair of forces by single force. c. Find the resultant of single force above.
Find the internal force systems acting on sections 1 and 2.
Find the resultant and angle of direction based on the horizontal. using tail to tip method A) 25 lb. 40 0N of E B) 10 lb 45 0N of W
1.2) Problem. 3 The following forces (all pull) act at a point : (i) 25 N due North ; (ii) 10 N North-East ; (iii) 15 N due East ; (iv) 20 N 30° East of South ; (v) 30 N 60° South of West. Find the resultant force. What angle does it make with East ?
Find the shear and moment equations for the beam loaded as shown if P = 220 lb, W = 213 lb/ft, a = 4.3 ft, and b = 15 ft. Then find the distance from C where the shear force is zero. Round off the final answer (in ft) to two decimal places.
7. If a force of 100 pounds is required to push a block upward an inclined purface 10 with the horizontal, what is the weight of the block? 8. 8. angle of elevation of the top of the tree from point A is 20P. At point 8, 50 m from A, the angle of elevation to the top of the tree is 22 How far is the tree from point B? 9. In order to determine the length of the bridge AB, a woman moves 250 m perpendicular to the bridge from point B to C and measures the angle at C to be 40 degrees What is the length of the bridge AB?

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L