Problem 5: A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation are: JA = B(t)x + B'(t)y' KA = B'(t)xy' JB = A'(t)x %3D KB = A(t) + xy' %3D z = A(t)x'y' + B(t)x'y' 1) Draw the logic diagram of the circuit. 2) Tabulate the state table. 3) Derive the state equations for A and B.

Problem 5: A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation are: JA = B(t)x + B'(t)y' KA = B'(t)xy' JB = A'(t)x %3D KB = A(t) + xy' %3D z = A(t)x'y' + B(t)x'y' 1) Draw the logic diagram of the circuit. 2) Tabulate the state table. 3) Derive the state equations for A and B.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A sequential circuit has two JK flip-flops A and B and one input x. The circuit is described by the following flip-flop input equations:JA = x, KA = B'JB = x’, KB = Aa. Derive the state equation A(t+1) and B(t+1) by substituting the input equations for the J and K variables. b. Draw the state diagram of the circuit.
A sequential circuit has two JK flip-flops A and B and one input x. The circuit is described by the following flip-flop input equations: Ja=x Ka=B' Jb=x Kb=A (a)* Derive the state equations A(t + 1) and B(t + 1) by substituting the input equations for the J and K variables. (b) Draw the state diagram of the circuit.
A sequential circuit has two JK flip-flops A and B and one input x. The circuit is described by the following flip-flop input equations: JA=x KA=B JB=x KB=A′1. (a) Derive the state equations A(t+1) and B(t+1) by substituting the input equations for the J and K variables.2. (b) Draw the state diagram of the circuit.
DIGIT ELECTRONICS : As a design engineer, you were assigned to produce warning lights in the hazard compound at the workspace. It required two input frequencies, 32kHz, and 8kHz tooperate the running light independently. By using a clock generator value of 128kHz,design a circuit that utilized the JK flip-flops to produce the required signal frequency.
Design a logic circuits w/ 4inputs (A(MSB), B,C,D(L,S,B)) and 1 output x. The 4 inputs represent switches in a vending machine. The switches can be either open (0) or closed (1) The X output becomes high if and only there are two or more switches closed at the same time. Furthermore it is impossible for the first A and the last switch D to be closed at the same time. Reqd: 1.) complete and labeled truth table 2.) canonical sop form expression 3.) grouped kmap 4.) minimum SOP expression
A sequential circuit with two D flip-flops A and B, two inputs, x and y; and one output z is specified by the following next-state and output equations A(t+1)=xy′+xB B(t+1)=xA+xB′ z=A. Draw the logic diagram of the circuit.
Design a combinational circuit (three inputs A, B, C) whose output (Y) is equal to 1 if (i) the input variables have more 0’s than 1’s, and (ii) the input variables have an even number of 1’s. The output is 0 otherwise. Note: Obtain the circuit’s truth table, Boolean equation, and a logic diagram. Design the circuit using mux also.
Design a combinational circuit with three inputs (X, Y, & Z) and six outputs. The output (F, E, D, C, B, A) represents the square of the designated input. Find the Boolean expression of the output F. a. XY b. 0 c. 1 d. none of the choices
Flip flop input and output equations for a sequential circuit with 2 flip flops (A and B), 1 input (X) and 1 output (Z) are as follows. Create a state table for the circuit and draw the state diagram of the circuit. Write whether the circuit is a Mealy or Moore circuit and explain why. A(t+1) = A’X + BX' B(t+1) = AX’ + B'X Z = A’B'X'
A sequential circuit with two D flip-flops A and B, two inputs, x, and y; and one output z is specifiedby the following next-state and output equations.A(t + 1) = xy' + xBB(t + 1) = xA + xB'z = A• Draw the logic diagram of the circuit• List the state table for the sequential circuit• Draw the corresponding state diagram
Flip flop input and output equations for a sequential circuit with 3 flip flops (A, B and C), 2inputs (X and Y) and 1 output (Z) are as follows. Create a state table for the circuit anddraw the state diagram of the circuit. State whether the circuit is a Mealy or Moore circuitand explain why? A(t+1) = A’Y + BX’B(t+1) = AX’ + B’YC(t+1) = AZ = A’B + X’Y
A sequential circuit with two D flip-flops A and B, two inputs, x and y; and one output z is specified by the following next-state and output equations A(t + 1) = xy+ A'y Bt + 1) = xB + B' + xB° z= A'B (a) Draw the logic diagram of the circuit. (b) Draw the corresponding state diagram.