Design a logic circuits w/ 4inputs (A(MSB), B,C,D(L,S,B)) and 1 output x. The 4 inputs represent switches in a vending machine. The switches can be either open (0) or closed (1) The X output becomes high if and only there are two or more switches closed at the same time. Furthermore it is impossible for the first A and the last switch D to be closed at the same time. Reqd: 1.) complete and labeled truth table 2.) canonical sop form expression 3.) grouped kmap 4.) minimum SOP expression

Design a logic circuits w/ 4inputs (A(MSB), B,C,D(L,S,B)) and 1 output x. The 4 inputs represent switches in a vending machine. The switches can be either open (0) or closed (1) The X output becomes high if and only there are two or more switches closed at the same time. Furthermore it is impossible for the first A and the last switch D to be closed at the same time. Reqd: 1.) complete and labeled truth table 2.) canonical sop form expression 3.) grouped kmap 4.) minimum SOP expression

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

A logic function f(A,B,C) implemented with 4x1 MUX circuit. Implement the same function with using only one 4x1 MUX. (B and C are selection inputs B=S1; C=S0)
5) You want to design an arithmetic comparison combined logic circuit.a. Write your design purpose of the 4-bit comparison (big-equal-small) circuit.b. List the process steps that you will apply in the design approach. Design a 4-bit comparison (large-equal-small) circuit. Explain each step. Realize with AND, OR, NOT gates.c. Compare the decimal numbers in the last two digits of your student number in the circuit you designed and discuss the result. last two digits of student number : 0 4 . Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, Because it is normal when solving a question to have tables and equations. I want an integrated solution, please look at the question carefully before starting the solution because I have sent a question a lot
. Design a logic circuit that controls an elevator door in a three-story building. The circuithas four inputs. M is a logic signal that indicates when an elevator is moving (M=1) or stopped (M=0).F1, F2 and F3 are floor indicator signals that are normally LOW, and they go HIGH only when theelevator is positioned at the level of that particular floor. For example, when the elevator is lined uplevel with the second floor, F2=1 and F1=F3=0. The circuit output is the OPEN signal which isnormally LOW and is to go HIGH when the elevator door is to be opened.
You want to design an arithmetic comparison combined logic circuit. (a) List the steps that you will apply in the design approach. Design a 4-bit comparison (large-equal-small) circuit. Explain each step. With AND, OR, NOT gatesmake it happen. (b)By comparing the numbers 9 and 1 in the circuit you designed, the resultdiscuss.
Design, a digital logic circuit in tinkercad that accepts inputs A, B and C from plane A, Band C. An input value of “1” indicates that the corresponding plane is requesting permission toland on the runway. For example, if A=1 then there is a plane A is requesting permission to landon the runway.Plane A has the highest priority, B has the next priority level and C has the lowest priority.Meaning that A always gets to use the runway regardless of other requests and C only gets to usethe runway if A and B are not requesting permission.Circuit outputs are LandA, LandB and LandC where the value “1” means the correspondingplane has permission to land. For example, if LandB=1 then a plane B is permitted to land onthe runway. Although you may have landing requests for more than one plane, only one planemay be granted the permission to land.For this experiment, generate the input using 3 switches and simulate the output using 3 LEDs.For this lab, only use AND, OR, and INVERTER (NOT) gates
Logic Circuit Diagram – what will the result be for the following circuit if a = 1, b = 0, and c = 1? ___.
Question If 4 tanks are used as a water reservoir. It is important to keep check on those tanks which have gone empty. If a very basic check is required to check if 3 out of 4 tanks are empty or not, to make sure that water supplier should be called to refill reservoir tanks when there’s only one tank left with water and all other three are empty. You are required to make a basic logic expression and then make it’s circuit using basic logic gates, which can perform this task of identifying if any of three tanks are empty. Each empty tank can be used as logic ‘1’ and non-empty tank as logic ‘0’.
Subject: Digital Logic Design Paint Manufacturing plant.A liquid chemical is used in a manufacturing process. The chemical is stored in three different tanks. A level sensor in each tank produces a HIGH voltage when the level of chemical in the tank drops below a specifiedpoint. Design a circuit that monitors the chemical level in each tank and indicates when the level in any two of the tanks drops below the specified point. Write the Boolean SOP expression for the the Circuit.
A water purification plant uses one tank for chemical sterilization and a second larger tank for settling and aeration . Each tank is equipped with two sensors that measure the height of water and the flow rate respectively . When the height of water or flow rate is too high the sensors produce a logic high output . Design a logic circuit that sounds an alarm whenever the height of water in both tanks is too high and either of the flow rates is too high , or whenever both flow rates are too high and the height of water in either tank is also too high.
Please can you help me And solve this problem I hope it includes a solution the k-map and logic circuit diagram
A water purification plant uses one tank forchemical sterilization and a second, larger tank forsettling and aeration. Each tank is equipped with twosensors that measure the height of water in each tankand the flow rate of water into each tank. When theheight of water or the flow rate is too high, the sensorsproduce a logic high output. Design a logic circuit thatsounds an alarm whenever the height of water in bothtanks is too high and either of the flow rates is toohigh, or whenever both flow rates are too high and theheight of water in either tank is also too high.
question from DIGITAL LOGIC DESIGN book Sequential Logic :2. Perform Analysis Procedure on the following Circuit. Finally, do not forget to comment on the behaviorof the circuit. Perform all necessary analysis steps.and aslo perform each step.