Problem 5 The state of stress at a point is shown on the element. Determine (a) the principal stress and (b) the maximum in-plane shear stress and average normal stress at the point. Specify the orientation of the element in each case. Sketch the results on each element. Solve the problem using the formula comparing to Mohr's Circle. 60 MPa 30 MPa 45 MPa

Problem 5 The state of stress at a point is shown on the element. Determine (a) the principal stress and (b) the maximum in-plane shear stress and average normal stress at the point. Specify the orientation of the element in each case. Sketch the results on each element. Solve the problem using the formula comparing to Mohr's Circle. 60 MPa 30 MPa 45 MPa

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 52PQ

See similar textbooks

Similar questions

Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
The bulk modulus of a material is 1.01011N/m2 . What fractional change in volume does a piece of this material undergo when it is subjected to a bulk stress increase of 107N/m2 ? Assume that the force is applied uniformly over the surface.
Explain why the viscosity of a liquid decreases with temperature—that is, how might increased temperature reduce the effects of cohesive forces in a liquid? Also explain why the viscosity of a gas increases with temperature—that is, how does increased gas temperature create more collisions between atoms and molecules?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Review. On a day that the temperature is 20.0C, a concrete walk is poured in such a way that the ends of the walk are unable to move. Take Youngs modulus for concrete to be 7.00 109 N/m2 and the compressive strength to be 2.00 109 N/m2. (a) What is the stress in the cement on a hot day of 50.0C? (b) Does the concrete fracture?
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
A hollow member having the cross section shown is formed from steel alloysheet of 2mm thickness. Knowing that the shearing stress must not exceed 3MPa, (a) determine the largest torque that can be applied to the member and (b) using the largest torque calculated in (a), determine the angle of twist (Shear modulus of steel alloy is assumed 75 GPa).
A rectangular piece of wood, 50 mm x 100 mm in cross-section isused as a compression block as shown in the figure. Determine the maximumaxial load P which can be safely applied to the block if the compressive stress inthe wood is limited to 20 MPa.
For the beam and loading shown, determine the maximum absolute value of bending moment and shear.
Two parallel and opposing forces of each value (4000N) act tangentially on opposite sides of a cube of metal of side length (25cm). Calculate the displacement of the top surface relative to the bottom surface. If you know that the shear modulus of the metal is equal to (80GPa)?
1. By method of sections, determine the force in member CD, CF, and FG of the Warren truss. Solve for the forces, axial stresses and the factors of safety if the member is a solid-circular cross-section that has a diameter of 30 mm and a maximum allowable stress of 10kN/m^2.
Write Griffith’s expression for the fracture stress of a material under plane stress conditions. Identify which parameters are applied and which are material constants