PROBLEM 6-An open trapezoidal tank having a bottom width of 3 m is 2 m high, 1.5 m wide, and has its sides 60° with the horizontal. It is filled with water to a depth of 1.5 m. if the tank is accelerated horizontally along its length at 4.5 m/s^2, how much water is spilled out? 2 m 1.5 m 1.9 m^3 2.9 m^3 3.9 m^3 4.9 m^3 5.9 m^3 None of the above 3 m During the motion: 60° a=4.5 m/s² *

PROBLEM 6-An open trapezoidal tank having a bottom width of 3 m is 2 m high, 1.5 m wide, and has its sides 60° with the horizontal. It is filled with water to a depth of 1.5 m. if the tank is accelerated horizontally along its length at 4.5 m/s^2, how much water is spilled out? 2 m 1.5 m 1.9 m^3 2.9 m^3 3.9 m^3 4.9 m^3 5.9 m^3 None of the above 3 m During the motion: 60° a=4.5 m/s² *

Name: PROBLEM 6-An open trapezoidal tank having a bottom width of 3 m is 2
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: PROBLEM 6-An open trapezoidal tank having a bottom width of 3 m is 2 m high,1.5 m wide, and has its sides 60° with the horizontal. It is filled with water to adepth of 1.5 m. if the tank is accelerated horizontally along its length at 4.5m/s^2, how

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Inflow depth= h, hwater Water from a storm drain flows over an outfall with a height, h, = 0.25 m, and width into the paper of B = 5.0 m. The inflow has a velocity, Uin = 2.0 m/s, into a tank. You can assume that the water instantly spreads out over the surface in a smooth fashion so that the water level in the tank can be considered a flat surface of area A=BxL. At the bottom of the tank is a porous bed that absorbs the water at a uniform vertical velocity of V = 14.0 mm/s, as shown in the figure given below. The outflow at the bottom of the tank, Qout m³/s is equal the volume flux of water entering the filtration layer. The tank is B = 5.0 m deep into the paper and has a length L = 25.0 m. There is an initial depth of water on top of the porous bed of ho =29.0 mm. Find the height of the water, h,water (the ponding level) above the porous media at t = 11.0 seconds after the start of the storm. Please provide your answers to 5 significant figures. h = m
6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L s'. For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of the water gage. Determine the smallest standard commercial steel pipe that will give the required performance. pump 4.5 m. 1.8 19=d 3.5 m 7. water 90° elbow
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 3.1 Find the maximum allowable speed to operate the pump 3.2 What power is expected in overcoming friction at this speed, takef = 0.01
Question 3 Consider 2 which shows a pipe system connecting two reservoirs. The pipe diameter changes at point B as shown in the image A 10 cm 23 m NOT TO SCALE Figure 2: 9 m 6 cm с 3 m 1. Describe what is referred to by the hydraulic gradient line and the energy gradient line. What is the difference between the two levels? In what scenario will the energy and hydraulic grade lines coincide? 2. Calculate the velocities in the two segments of the pipe. Take into account the friction losses through the pipe, entry loss to the pipe and the shock contraction losses at B. Take the pipe friction factor as 0.005 and the coefficient of contraction at B as 0.6. 3. Draw the energy gradient line and the hydraulic gradient line for the system.
The water of a 14’ × 48’ metal frame pool can drain from the pool through an opening at the side of the pool. The opening is about h = 1.05 m below the water level. The capacity of the pool is V = 3740 gallons, the pool can be drained in t = 10.2 mins. P0 is the pressure of the atmosphere. ρ is the density of the water. a. Write the Bernoulli’s equation of the water at the top of the pool in terms of P0, ρ, h. Assuming the opening is the origin. b. Write the Bernoulli’s equation of the water at the opening of the pool in terms of P0, ρ, h and v, where v is the speed at which the water leaves the opening. Assuming the opening is the origin. c. Express v2 in terms of g and h. d. Calculate the numerical value of v in meters per second. e. Express the flow rate of the water in terms of V and t. f. Express the cross-sectional area of the opening, A, in terms of V, v and t. g. Calculate the numerical value of A in cm2
9. What is the diameter, in millimeter, of an orifice in a tank with a cross-section of 1.5 m² if the orifice draws down water at a rate of 160 mm/sec at a 3.35 m head? Use C = 0.63.
Current Attempt in Progress The pump shown in the figure below delivers a head of 250 ft to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 150 ft. Assume L= 200 ft, D=0.5 ft. - 1.0 Pump K - 1.5 ebow - 5.0 Pipe length - L Pipe diameter -D Pipe roughness -0 = 0.৪ ft-lb/s or i hp
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
A Francis radial-flow hydroturbine is being designed with the following dimensions: r2 = 2.00 m, r1 = 1.42 m, b2 = 0.731 m, and b1 = 2.20 m. The runner rotates at n. = 180 rpm. The wicket gates turn the flow by angle ?2 = 30° from radial at the runner inlet, and the flow at the runner outlet is at angle ?1 = 10° from radial. The volume flow rate at design conditions is 340 m3 /s, and the gross head provided by the dam is Hgross = 90.0 m. For the preliminary design, irreversible losses are neglected. Calculate the inlet and outlet runner blade angles ?2 and ?1, respectively, and predict the power output (MW) and required net head (m). Is the design feasible?
A Francis radial-flow hydroturbine is being designed with the following dimensions: r2 = 2.00 m, r1 = 1.42 m, b2 = 0.731 m, and b1 = 2.20 m. The runner rotates at n. = 180 rpm. The wicket gates turn the flow by angle ?2 = 30° from radial at the runner inlet, and the flow at the runner outlet is at angle ?1 = 10° from radial. The volume flow rate at design conditions is 340 m3 /s, and the gross head provided by the dam is Hgross = 90.0 m. For the preliminary design, irreversible losses are neglected. Calculate the turbine specific speed of the turbine. Provide answers in both dimensionless form and in customary U.S. units. Is it in the normal range for a Francis turbine? If not, what type of turbine would be more appropriate?