1. Figure Q1 shows a continuous beam with the roller support at A and B, and the pin support at C. Assume El is constant. a. Draw the free body diagram and show all reactions and loads. b. Determine all reactions at supports A, B, and C. c. Construct shear and moment diagrams. 55KN 13.5kN/m 2m 2m 4m Figure QI

1. Figure Q1 shows a continuous beam with the roller support at A and B, and the pin support at C. Assume El is constant. a. Draw the free body diagram and show all reactions and loads. b. Determine all reactions at supports A, B, and C. c. Construct shear and moment diagrams. 55KN 13.5kN/m 2m 2m 4m Figure QI

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(a) Figure Q2 shows a frame with tie rod at joint B and C. The beam carries a concentratedload 300kN at span BC. Analysis and sketch the shear force and bending-momentdiagram for the entire frame.
GIVEN: L1 = 4.5 m W1 = 10 kN/m L2 = 1.2 m W2 = 12 kN/m L3 = 0.5 m L4 = 12 m L5 = 1.5 m Draw the Shear and Moment Diagrams for: a. Beam A-B-C b. Beam D-E-B
For the beam presented below:a) What is the degree of indeterminacy; b) Determine the moment reactions at the supports and draw the shear and momentdiagrams. (Solve by expressing the internal moment in terms of vertical reactionsat A and B, EI is constant). c) What would the shear diagram look like if a transverse load P was applied right atthe middle of the beam (Make a sketch of the new shear diagram). W (30kN/m) , L (1.9m)
Set P=0.6 kN and w=1.20 kN/m. Consider A is a roller support and B is a pin support. Illustrate the shear and moment diagram of the beam below.
Determine the equation of the elastic curve for the overhanging beam, Calculate the value of EIongation midway between the supports, and Calculate the slope at the left support. EI = constant. Note: Draw and label properly the FBD and Shear and Moment Diagram.
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.2 ft, b = 3.3 ft, P = 22 kips, and w = 2.7 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
An indeterminate beam loaded a uniformly distributed load from A to B, from B to C, a linearly varying from 0 to 6 kN/m, is fixed at C, and a roller at point A and also in point B (where it settled 25 mm downwards here). The flexural rigidity is constant from A to C. Use E = 180 GPa, I = 1024 x 106 mm4 .Calculate the reactions and draw the shear and bending moment diagram for this beam using Slope Deflection Method.
Determine all reactions at supports. Determine the shear and bending moments with complete labels also. Use Moment Distribution Method; and use E = 2.15×10^7 kPa and I = 1/12 bh^3
- Use Force Method to analyse- For beams and frames, analyse all support reactions and draw the shearforce and bending moment diagrams. subtitute P with 2 p=2
Draw the shear-force and bending-moment diagrams for the beam shown. Determine the bending moment 3.16 ft to the right of point A if P = 3.47 kips and Q = 4.33 kips.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.8 ft, b = 3.5 ft, P = 30 kips, and w = 2.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.