Problem 8. Re-write the strain compatibility condition in the engineering notation. e22,33 +€33,22 = 2 €23,23
Q: 3.64 The resultant of the force-couple system acting on the frame is a force R acting at point A.…
A: Find the resultant force R and a horizontal force P when the resultant passing through the point A
Q: Compute the required diameter of an air cylinder piston rod of AISI 1040 hot-rolled steel. The rod…
A: Given data
Q: A thermometer has a time constant of 10 s and behaves as a first-order system. It is initially at a…
A:
Q: The accepted value of the specific heat of copper is 0.385 J/g °C. Calculate the percent error.
A: To calculate the percent error, we need to know the experimental value and the accepted value. If…
Q: Same problem is considered here again using three equal length elements. Suppose that the Young's…
A: Given: E = 19 GPa = 19×109 Pa P = 35 kN = 35000 N A1= 30 mm2 = 30×10-6 m2 Total length, L = 15 cm =…
Q: 3. A centrifugal pump is to be placed above a large, open water tank, as shown in the figure below.…
A: Given data: Q = 1 ft3/s Net Positive suction head required, NPSH = 15 ft T = 80 F Pa = 14.7 psi =…
Q: . The accepted value of the specific heat of copper is 0.385 J/g °C. Calculate the percent error.
A: To calculate the percent error, we need to know the experimental value and the accepted value. If…
Q: Small steel balls fall from rest through the opening at A at the steady rate of 3 per second. Find…
A:
Q: Determine the force in member BD of the regular pyramid with square base. The force is positive if…
A: Draw the free-body diagram of the regular pyramid.
Q: Problem 6. Consider the following stress state: [6 4 01 [a] 4 12 0 ksi Lo 0 6] Determine the…
A: Given: σ=6404120006 ksi Young's Modulus ,E=10000 ksi Poisson Ratio ν=0.25
Q: The concept of a weak solution of a boundary value problem plays an important role in some numerical…
A: To Find: The value does the weak formulations offer, and the possible shortcoming of the weak…
Q: Problem 2. Consider a rod with radius c, subject to shear force V. Clearly show the Neutral Axis on…
A: Givenshear stress τ=VQItwhereV is shear forceC is radius of the section
Q: Same problem is considered here again using three equal length elements. Suppose that the Young's…
A: Given data: Young's Modulus, E = 1 GPa = 1×109 pa applied force, P = 29 kN = 29000 N Area of element…
Q: The tongs are used to lift the 150-kg crate, whose center of mass is at G. Suppose that 0 = 26°.…
A: Given, Mass of crate = m = 150 kg Weight of crate = W = mg = (150) (9.81) = 1471.5 N Angle θ = 26o…
Q: Determine the tension developed in each cable for equilibrium of the 300-lb crate. 3 ft
A: According to the given data Coordinates of the point A=(0, 6, 0)ft B=(-3 , 0 , 2)ft C=(2 , 0 , 3)ft…
Q: Depending on the rate of loading (gradual, sudden or impact) the collar with the Load P, shown in…
A: To determine: The equation for the stress induced, assuming the collar is quickly loaded and the…
Q: PROBLEM 4: Find the reaction force components at point A and B. The member AB has a length of L=10m.…
A:
Q: Find the resultant of the following concurrent forces graphically and analytically: FI=100N 37°…
A:
Q: In the process where the product of pressure and the volume is constant, a gas compression is…
A: Given data:- Initial pressure(P1) =200 kPa final pressure(P2)=800 kPa initial specific volume (v1)…
Q: ᴀ ꜱᴛᴇᴇʟ ʙᴇ ʀᴏᴅ ᴏɴ ʙʀɪᴅɢᴇ ᴍᴜꜱᴛ ʙᴇ ᴍᴀᴅᴇ ᴛᴏ ᴡɪᴛʜꜱᴛᴀɴᴅ ᴀ ᴘᴜʟʟ ᴏꜰ 600 ʟʙꜱ, ꜰɪɴᴅ ᴛʜᴇ ᴅɪᴀᴍᴇᴛᴇʀ ᴏꜰ ᴛʜᴇ ʀᴏᴅ…
A: Given, Pull load = 600 LBS = 6000 LBS (Correction) Factor of safety = 5 Ultimate stress = 64000 PSI…
Q: A system of three tanks is connected as shown. The flow net formed by the tanks and their piping…
A: Given Data: The known mass flow rates, m1 = 15 lbm/sm3 = 20 lbm/sm5 = 12 lbm/s Solution: Sub Part…
Q: ᴀɴ ɪʀᴏɴ ʀᴏᴅ 4 ᴍ ʟᴏɴɢ ᴀɴᴅ 0.5 ᴄᴍɴ ɪɴ ᴄʀᴏꜱꜱ ꜱᴇᴄᴛɪᴏɴ ꜱᴛʀᴇᴛᴄʜᴇꜱ 1 ᴍᴍ ᴡʜᴇɴ ᴀ ᴍᴀꜱꜱ ᴏꜰ 225 ᴋɢ ɪꜱ ʜᴀɴɢ ᴏɴ ɪᴛ…
A:
Q: Consider the composite wall below. The inner side of the wall is subjected to air flow at 430°C with…
A:
Q: Same problem is considered here again using three equal length elements. Suppose that the strain…
A: Given Data Strain energy of element 1 ( U1) = 0.07 N.m Strain energy of element 2 ( U2) = 0.17 N.m…
Q: Does the following pass the "test" of novelty? A design for a chair that folds. Passes test…
A: A chair that folds is a common design that has been implemented in numerous products already.…
Q: • A barge is pulled by two tugboats. If the resultant of the forces exerted by the tugboats is 5000…
A: According to the given data R=5000N α=45° We need to find Force in the member 1 and 2
Q: Two 20-mm steel plates are butt-welded together. Both the plate and the welding = 500 MPa and…
A: Given data: Plate thickness, t = 20 mm Load fluctuates from -20 kN to 60 kN Ultimate strength, Su =…
Q: If a wheel is subjected to a torque of 180 ft-lbs and the wheel's outer diameter is 14", what force…
A: This question is based on the concept of Mechanics.
Q: the work, in kJ. a result of 10 ni vgrons ainstoq Isnoistivity on 2.22 Air contained within a…
A:
Q: An iceberg having a specific gravity of 0.92 is floating on sait of the ice below water of specific…
A: Given: Specific gravity of Iceberg= 0.92 Specific gravity of Salt water= 1.03 Volume of immerged…
Q: Consider a pipe-pipe configuration consisting of concentric steel tubes with an intervening…
A: Given Di1=150mmti=to=10mmDi2=250 mmho=500 W/m2Kks=35 W/mKkp=0.075W/mKhi=450 W/m2K
Q: A steel bar having known Sut (1200 MPa) and Sy (950 MPa) has a fine ground surface. Determine the…
A: Given: Sut=1200 MPaSy=950 MPa Solution: Assumption: For the fine ground surface , Ka=a(Sut)b…
Q: Q. Calculate the deflection at midspan for the s.s. beam in Fig. 7. lekN/m EI Fig. 20kN/m 1 2 ET 4m…
A: The deflection is given as: δ=∫abM0M1EIdxhere,M0=moment equation for primary structureM1=moment…
Q: Solution please. Should 100% correct Each strut has a cross-section as shown in Figure Q5. Solve for…
A: Find the second moment of area about centroidal axis
Q: Part A A simply supported shaft is shown in the figure below. Assume the following data: a = 16 in,…
A:
Q: Show how the equation below was derived. Provide a complete solution with an explanation. PC- PB Pa…
A: Draw the given diagram.
Q: A 0.2-m³ tank contains 8.6×10²6 molecules of CO₂ at 15 MPa. Compute the (a) specific volume. Also,…
A: To compute the specific volume, we can use the ideal gas law: PV = nRT where P is the pressure, V is…
Q: Air undergoes an Atkinson Cycle. The air is compressed from 1 bar, 17 C to 5 bar. The maximum…
A: The given information in the problem is shown in the following attached image:
Q: Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a…
A: The diameter of pipe is d=70 cm=0.7 m. The height of reservoir is h=95 m. The power output from…
Q: 1) Determine the reaction force at support A.
A:
Q: Questions about noise: (1) In the Dorben Co., an all-day study revealed the following noise sources:…
A: “Since you have posted multiple questions, we will provide the solution only to the first question…
Q: Determine the pressure acting on a surface of 1.27 m2 if the force applied to the surface is 52 N
A: Given:Surface area, A=1.27 m2Force applied to the surface, F=52 NFind:The pressure acting on the…
Q: More Ground-ground Ballistics 1. A baseball is thrown upward with a speed of 24.0 m/s and an angle…
A:
Q: 2. A spherical tank contains 100 kg of Hydrogen at 15 MPa and 40°C, find the volume and diameter of…
A: According to the given data m=100kg T=40deg=313.15 k P=15 MPa We need to find The volume of the tank…
Q: 6. A 1.5 L of water at 90°C is mixed with a cold water (10 L at 10 °C) to warm it up. Find the…
A:
Q: 4 Pre-Lab 4.1 Equations Governing the Cart Dynamics Derive the following equation of motion for the…
A: Given: To find: Derive equation
Q: Refrigerant-134a enters the compressor of a refrig- erator at 100 kPa and -20°C at a rate of 0.5…
A: The refrigerant enters the compressor at 100 kPa and -20°C. The refrigerant flow rate is 0.5 m3/min.…
Q: A ferry is moving due east and encounters a southwest wind of speed vw = 11.0 m/s as shown. The…
A: According to the given data vw=11.0 m/s θ=37 ° We need to find Speed vB
Q: The relation which states that the rate of heat loss of a body is directly proportional to the…
A: According to the question The relation which states that the rate of heat loss of a body is directly…
Q: • Assume that the water main has a huge diameter, such that the water velocity is effectively zero…
A: To Find : The velocity of water is coming of the hose. Given : The density of water is ρ=1000 kgm3…
Step by step
Solved in 2 steps
- Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
- An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a) Determine the strains for an element oriented at an angle = 250. (b) Find the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
- An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 30°. (b) Determine the principal strains of the clement. Confirm the solution using Mohr’s circle for plane strain.On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
- A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.