PNEUMATICSsolve the problem using festo fluidsim. Put all the details Problem #3: Use of 5/2 way valves with spring returnProblem:Boxes (or certain production parts) are moved by a double-actingcylinder away from a gravity-feed magazine towards an assemblydevice.A push button and a pedal switch are to be incorporated in thecircuit. The cylinder is to move out when either of these isactuated.The return stroke is actuated by the cylinder rod after it reachesthe end of the forward stroke.Positional sketch:

This problem is solved using Pneuma solver software.

Problem: Boxes (or certain production parts) are moved by a double-ac cylinder away from a gravity-feed magazine towards an asser device. A push button and a pedal switch are to be incorporated in th circuit. The cylinder is to move out when either of these is actuated. The return stroke is actuated by the cylinder rod after it reach

Problem: Boxes (or certain production parts) are moved by a double-ac cylinder away from a gravity-feed magazine towards an asser device. A push button and a pedal switch are to be incorporated in th circuit. The cylinder is to move out when either of these is actuated. The return stroke is actuated by the cylinder rod after it reach

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter23: Compressors

Section: Chapter Questions

Problem 9RQ: Describe the reciprocating compressor piston, rod, crank-shaft, valves, valve plate, head, shaft...

See similar textbooks

Similar questions

Calculate the valve flow coefficient for the 5/2 double-pilot valve controlling the work cylinder. Assume acylinder stroke of 6”, an extension time of 1.0 sec, a retraction time of 0.5 secs. and ΔP=5 psi.
Devise a ladder program that can be used with a solenoid valve-controlled double-acting cylinder, that is, a cylinder with a piston that can be moved either way by means of solenoids for each of its two positions, and moves the piston to the right, holds it there for 2 s, and then returns it to the left.
In not more than 3 sentences, Explain what will happen to a double-acting cylinder if equal pressures are applied to its two ports assuming the piston is initially at midpoint position.
What size of receiver tank (gal) for a compressor is required if the pneumatic system is used to drive 5 linear cylinders which collectively consume 12 SCFM for 5 minutes? The compressor pressure switch operates between 90 and 110 psi.
List the functions of a pneumatic valve.
The rest of the questions are thus: 4) Calculate the air temperature and pressure in the pump at the end of the following expansion stroke, just before the piston uncovers the orifice (orifice dimensions are neglectable).5) Calculate the mass and temperature of air in the pump (i.e. the cylinder andconnecting pipe) after the orifice has been exposed and the pressure has risen to atmospheric pressure (bottle valve is now closed).7) Calculate the piston position and the air temperature in the pump during the next compression stroke at the time when the valve to the gas bottle opens again.8) Calculate the pressure in the bottle when no more air can be transferred by the pump. (This will be after an undetermined number of pumping cycles).
In a pressure regulator, the ________ is attached to one end of the poppet to provide a surface for the spring to push on.
Functionality of each compoenent, from prime mover to propeller. List the main propulsive losses and give an approximate magnitude to each
Match the fluid power system with its suitable applications/equipment
In the figure below, the cylinder rod does not extend when the directional control valve is actuated. The torque required to turn the load is 575 lb-in, and the pressure relief valve is set at 1,000 psi. What should be done to make the cylinder rod extend and retract?
Illustrate the reciprocating action of piston inside the cylinder taking into consideration for suction and delivery of liquid from lower level to higher level, with neat diagram.
Describe working principle of pressure-compensated flow control valve