Problem Sets 3: The cast iron inverted T-section supports two concentrated loads of magnitude P as shown. Determine the largest allowable value of P if the working stresses in bending are limited to 48 MPa in tension, 140 MPa in compression and shearing stress of 30 MPa. 15mm P 150mm ++] B D 1m 3m 1m- 15mm 150mm

Problem Sets 3: The cast iron inverted T-section supports two concentrated loads of magnitude P as shown. Determine the largest allowable value of P if the working stresses in bending are limited to 48 MPa in tension, 140 MPa in compression and shearing stress of 30 MPa. 15mm P 150mm ++] B D 1m 3m 1m- 15mm 150mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear Determine the location of centroid, y, from top of the beam in mm Determine the moment of inertia, I, of the section in mm^4. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam Determine the maximum flexural stress on the beam in MPa.
Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine thefollowing: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle baris 60 MPa. Thickness of angle bar B is 6 mm.b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is25 MPa. Thickness of angle bar is 5 mm.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.
Taking into account only the effect of normal stresses, determine the strain energy ofthe prismatic beam AB for the loading shown. M0 (11kNm), L (3.4m), a (1cm), b (7cm) , d (14cm) , E (185GPa) , G (75GPa)
Give me the solution. Question: Identify the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Thickness, tf=9mm Flange Width, B=112.5 mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear 1. Determine the location of centroid, ȳ, from top of the beam in mm
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 3. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. 4. Determine the location of the maximum moment on the beam in meters.
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 7. Determine the maximum shearing stress on the beam in MPa. 8. Determine the flexural stress, In MPa, on the fiber 30mm above NA at distance 1m from A
Determine the concentrated load at midspan that can be added if theuniformly distributed load ω is 58 N/m that can beloaded for the beam shown if the allowable bending stress fortension is 80 MPa;, for compression is 130 MPa , for shearing stressis 48 MPa without exceeding deflection limit of L/360. E for steel is200 GPa.
A horizontal beam AD is supported by an inclined strut CB carries a load W = 2.4KN at the position shown. The strut which consists of one bar is connected to the beam by a bolt passing through the three bars meeting at joint C. BC is 75mm wide and 10mm thick strut while AD is 100mm wide by 10mm thick rigid bar. (a)What is the minimum required bolt diameter in at C if the allowable bolt shear is 68MPa? (b)Determine the stress in strut BC. (c)Determine the bolt stress at A if its diameter is 20mm.
Find the value of maximum load P sothat the stresses in the frame illustrated willnot exceed 120MN/m2 in tension or 90MN/m2in compression.The bars of the pin-connected frame shownhave a section of 35mmx65mm each.