Problem. The three-hinged arch supports the service load shown. The arch will tend to "kick" outward at the base. To avoid shear failure of the pins at the external hinge supports, tie rod is used to absorb the horizontal reactions at A and B. Using A36 steel and ASD, determine the required diameter (mm) of the round tie rod with threaded ends on the circular arch. A P 1 6m P = (Number of letters in family name) x 15 internal hinge tie rod = 6m Δ Β KN

Problem. The three-hinged arch supports the service load shown. The arch will tend to "kick" outward at the base. To avoid shear failure of the pins at the external hinge supports, tie rod is used to absorb the horizontal reactions at A and B. Using A36 steel and ASD, determine the required diameter (mm) of the round tie rod with threaded ends on the circular arch. A P 1 6m P = (Number of letters in family name) x 15 internal hinge tie rod = 6m Δ Β KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P (kN)= 7 allow=45 Pin C=double shear Pin D=single shear
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
Draw SFD and BMD for a cantilever carrying UDL for a part of its length from the free end.
Determine the slope at the roller B of the double overhang beam shown. Take E = 200 GPa, I = 18(106) mm4.
A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 8-ϕ25 mm equally distributed along all faces. Lateral ties are composed of 12 mm rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f’c = 27 MPa and steel yield strength, fy = 415 MPa.Calculate the nominal axial strength of the column in kN.A. 7 047 B. 5 638C. 4 580 D. 6 342 Calculate the center to center spacing of ties for confinement.A. 200 B. 400C. 500 D. 300 Where is the plastic centroid measured from the short edge of the column?A. 200 B. 400C. 500 D. 300 Calculate the steel stress (MPa) in the middle layer of bars at balanced strain condition.A. 31.37 comp B. 43.52 compC. 31.37 tension D. 43.52 tension Calculate the nominal axial strength in kN of the column at balanced strain condition considering bending about the strong axis.A. 3,420 B. 2,500C. 2,875 D. 3,846
A steel plate of dimensions 2.5 X1.5 X 0.08 mand weighing 23.1 kN is hoisted by steel cables withlengths L1 = 3.2 m and L2 = 3.9 m that are eachattached to the plate by a clevis and pin (see figure).The pins through the clevises are 18 mm in diameterand are located 2.0 m apart. The orientation anglesare measured to be θ = 94.4° and α = 54.9°.For these conditions, first determine the cableforces T1 and T2, then find the average shear stressτaver in both pin 1 and pin 2, and then the averagebearing stress σb between the steel plate and each pin.Ignore the weight of the cables.
Determine the angle of twist of the shaft at A relative ot C. Use Gst= 11.0 x 103 ksi.
16 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Bx = ?A) 3.75B) None.C) 18.75D) 0E) 30
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) the area of steel reinforcement corresponding to rho max in mm2.b.) the location of the point of zero shear in the beam measured from the left support B in mm.c.) Calculate the maximum positive moment in the beam in kN.m.d.) Calculate the required reinforcement Asreqd corresponding to the maximum positive moment in mm2.e.) Calculate the depth of the compression block of the final positive moment section in mm.f.) Calculate the depth of the neutral axis of the final positive moment section in mm.g.) What is the ultimate moment capacity of the final positive moment section in kN.m.h.) Calculate the additional positive moment that can be imposed to the beam without exceeding the moment capacity of the final positive moment section in kN.m.
Using the method of sections, calculate the forces in members £/ and JC of the truss shown and state if the members are in tension or compression. The truss is supported by a pinat Aand a cable at D. E 300016 1000 Ib -—(HIT()HH-—&HH
Compute the horizontal and vertical components of the hinge at point C and D on the frame system shown.
The column shown has a uniform rectangular cross-section. b = 14 mm and d = 24 mm. Assume both ends A and B are pinned supports.This Column ACB is laterally braced at its midpoint C suchthat rotation is allowed but translation is prevented alongthe y-axis direction.Use E = 200 GPa, and assume L = 600 mm.Knowing that a factor of safety of F.S. = 3.3 is required andusing Euler’s formula, determine the largest allowablecentric load Pall that can be applied to the column.