Problem2: The four arms of a Wheatstone bridge are as follows: AB = 100 Q, BC = 1000 Q, CD =O 4000 2, DA = 400 Q. A galvanometer with internal resistance of 100 N and sensitivity of 10 mm/HA isoconnected between AC, while a battery of 4 V dc is connected between BD. Calculate the current through.the galvanometer and its deflection if the resistance of arm DA is changed from 400 to 401 Q

Answered: Image /qna-images/answer/0148f82d-d79a-467d-b846-ca99f9458180.jpg

Problem2: The four arms of a Wheatstone bridge are as follows: AB = 100 0, BC = 1000 0, CD = 4000 Q, DA = 400 Q. A galvanometer with internal resistance of 100 and sensitivity of 10 mm/µA is Oconnected between AC, while a battery of 4 V dc is connected between BD. Calculate the current through .the galvanometer and its deflection if the resistance of arm DA is changed from 400 Q to 401 0

Problem2: The four arms of a Wheatstone bridge are as follows: AB = 100 0, BC = 1000 0, CD = 4000 Q, DA = 400 Q. A galvanometer with internal resistance of 100 and sensitivity of 10 mm/µA is Oconnected between AC, while a battery of 4 V dc is connected between BD. Calculate the current through .the galvanometer and its deflection if the resistance of arm DA is changed from 400 Q to 401 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2: Design series ohmmeter using PMMC of 100Ω internal resistance and 0.4ma full-scale deflection current. The required half-scale deflection is equal to 9kΩ.[use a battery of 9v]. Sketch the internal circuit diagram of the ohmmeter. Sketch also roughly the scale of the designed meter.
The sun’s output power is given as 1000 W/m2. The solar module has a surface area of 1 m^2 with a conversion efficiency of 10%. A charge controller converts the 20V module voltage to 12V battery voltage, with an efficiency of 84% The battery is 12V with a capacity of 10Ah. Assuming the battery is half empty and the bulb is powered on, how long will it take for the battery to be fully charged? How long can the bulb be powered at night, assuming full battery when the sun goes down and that you can fully drain the battery
The current in the circuit above is 0.5 A. We will refer to the battery on the left as 1, and the battery on the right as 2. Now start at a and “walk” with I. Use the fact that ∑V=0. The voltage contribution at b is A)IR. B)Vab. C)0 D)−Vab. Potential difference across the terminals of the right battery? Voltage contribution due to the internal resistance in the right battery? A)0; 0 B)−ϵ2; Ir2 C)ϵ2; Ir2 D)ϵ2; Potential difference across the terminals of the left battery? Voltage contribution due to the internal resistance in the left battery? A)0; 0 B)ϵ1; −Ir1 C)ϵ1; Ir1 D)−ϵ1; What is the electric power supplied by the 9 volt battery? A)4.3 watts B)1 watt C)3 watts D)0 What is the rate at which chemical energy is stored in the 6 volt battery? A)3 watts B)1 watt C)4.3 watts D)0
You are designing a new eco-friendly thermal coffee mug. It is shaped like a small globe to minimize surface area, which is only about 0.04m^2. You use two 0.003m layers of recyclable PETE which has a thermal conductivity, k, of 0.2W/mK around a 0.01m layer of dead air, with a thermal conductivity of 0.026W/mK. Since this is for hot coffee, use a temperature difference of 40K. Q = Ax (T2-T1) / (R1 + R2 + etc) R =x/k. What is the R-value for each of the two PETE layers
An aluminum wire 7.5m long is connected in parallel with a copper wire 6m long. When a current of 5A is passed through the combination, it is found that the current in the aluminum wire is 3A. If the diameter of the aluminum wire is 1mm, determine the diameter of the copper wire. Assume the resistivity of copper to be 0.017µΩm and that of aluminum to be 0.028 µΩm. Major Topic 7 Factors that affect the resistance
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
If the same meter movement in no.4 is used to construct a multi range voltmeter whose ranges are 5 V, 10 V and 15 V, find the required resistances for the following configuration: a. Basic multi-range voltmeter b. Commercial multi-range voltmeter (given in no.4: A 3-V DC voltmeter is composed of a 500-Ω meter movement in series with a 2500-Ω series resistance.)
a) The power, P, consumed by a resistor of resistance R, is given by P = E^2R Given that E = 20 V and R = 1000ꭥ, using partial derivatives, find the approximate change inpower if E is decreased by 0.5 V and R is increased by 50ꭥ.b) Check and compare your findings using standard electrical principles.
2.1 Explain why the adjusted value of R2 is equal to the internal resistance of the basic meter in Fig. 4. 2.2 Assume that we are given a basic meter having an internal resistance of 50ohm and a full-scale deflection of 1 mA. a) Design an ammeter having a full-scale deflection of 10mA. b) Design a voltmeter to measure a full-scale voltage of 30V. 2.3 Consider the circuit diagram in Fig. 3 and V(dc)=3V. a) When a-b are short-circuited, determine the value of Rv for full-scale deflection. b) Find the value of the unknown resistor Rx, if the meter current is 0.33mA.
(BASIC ELECTRICAL ENGINEERING) A solenoid has a length of 88cm and has a core of free air. It is wound with 4600 turns of wire and inductance of 278,000 micro Henry. What is the cross sectional area of the Solenoid in cm2 ?Show complete solution and limit your answer into 3 decimal.
Objectives: Voltage drop measurements using resistors connected in series. The relationship between resistance value and voltage drop (Kirchhoff’s Second Law) Circuit components: 1 Plug-in board, DIN A4 576 74 1 STE resistor, 100 W, 2 W, 5% 577 32 1 STE resistor, 150 W, 2 W, 5% 577 34 1 STE resistor, 1 kW, 2 W, 5% 577 44 Power Supply: 1 AC/DC stabilizer 726 88 Connectors: 3 Pairs of connecting leads, red/blue, 50 cm 501 45 1 Set of 10 bridging plugs 501 48 Measurement Instruments: 1 Voltmeter, 10 V DC 1 Amperemeter, 10 mA DC Measuring the voltage drop across resistors…
QUESTION TEXT A potentiometer consisting of a wire of length = 10 cm has a source of emf, ɛ = 15V connected across it. When a standard cell with emf V = 6V, in series with a voltmeter, is connected at one end of the wire and at a distance L along the wire the voltmeter circuit is in balance and the voltmeter reads zero. What is the value of the balance length L? Select one: a. 1.5 cm b. 4.0 cm c. 6.0 cm d. 2.0 cm