The elements in the DC bridge circuit shown in the below figure have the following values: R1= R2 = R3 = 300 N , Vị = 10 V. Consider the unknown resistance Ru is a platinum resistance thermometer with a range of 0°- 50°C, whose resistance at 0°C is 300 N and whose resistance varies with temperature at the rate of 2 2 /°C. Calculate the output voltage (i.e., Vo ) at 0°C, 25 °C, and 50 °C (assuming the internal resistance of the voltmeter is neglected) . Ru V, Vo

The elements in the DC bridge circuit shown in the below figure have the following values: R1= R2 = R3 = 300 N , Vị = 10 V. Consider the unknown resistance Ru is a platinum resistance thermometer with a range of 0°- 50°C, whose resistance at 0°C is 300 N and whose resistance varies with temperature at the rate of 2 2 /°C. Calculate the output voltage (i.e., Vo ) at 0°C, 25 °C, and 50 °C (assuming the internal resistance of the voltmeter is neglected) . Ru V, Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1) Conduct an evaluation on the practical applications of the concepts of electromagnetism and submit a written report which includes the following. a) Design a circuit which utilizes the concept of electromagnetism and submit a simulation circuit for the same (use simulation tool of your choice) b) Write down the selected values of the components used for example the values of resistors, transistor used, capacitors etc c) Obtain the output for the ciruit using any sinks like CRO, loud speakers etc. d) Discuss about the principles of electromagnetism used in the simulation I WANT QUESTION (D)
1. A thyristor operating from a peak supply voltage of 400 V has the followingspecifications:Repetitive peak current, Ip = 200 A, = 50 A/µs, = 200 V/ µs. Choosing a factor safety forthe above-mentioned parameters, design a suitable snubber circuit. The minimum valueof load resistance is 10 Ω. 2. A boost converter with vin = 12 V is required to be designed for a 100 W rating. If theoutput voltage is maintained at 96 V, find out load resistance and duty ratio. Furtherdesign the filter components in consideration with a ripple of 10% and 5% in inputcurrent and output voltage. Take the switching frequency be 30 kHz. 3. Following are the specifications of a thyristor operating from a peak voltage supply of500 V: Repetitive peak current, Ip = 250 A, = 60 A/µs, = 200 V/µs. Take the factor ofsafety of 2 for the three specifications mentioned above. Design a suitable snubber circuitif the minimum load resistance is 20 Ω. Take ξ = 0.65. 4. A buck–boost converter operating at 20 kHz, L = 0.05 mH.…
In the circuit given in the figure VT = 25mV, | VBE | = 0.7V, R1 = 515.22Kohm, R2 = 10.89Kohm, R3 = 2.41Kohm, R4 = 1.03Kohm, VCC = 12.00V, VEE = 2.00V, VA = 12.51V, Beta Since = 107.00, Rs = 23.19ohm, Ry = 8.18Kohm, calculate the IC current, Ri, R0 and voltage gain according to the Source (V0 / V1) by making full analysis.
A moving-coil instrument, which gives full-scaledeflection with 15 mA, has a copper coil having a resistance of 1.5 Ω at 15 °C, and a temperature coefficientof 1/234.5 at 0 °C, in series with a swamp resistor of3.5 Ω having a negligible temperature coefficient.Determine: (a) the resistance of shunt required for afull-scale deflection of 20 A; (b) the resistance requiredfor a full-scale deflection of 250 V. If the instrumentreads correctly at 15 °C, determine the percentageerror in each case when the temperature is 25 °C.
Calculate IR, determine the voltage Vce2 and the dynamic resistance re3 of Q3. Assume that VT = 25mV and Vbe = 0.7V
For a particular thermocouple, if one junction is maintained at 0˚C (cold junction) and the other junction is used as a probe to measure the desired Celsius temperature t, the voltage generated in the circuit related to the temperature t as ϵ = r(a + bt). Further, for this thermocouple, when ϵ is, in millivolts, the two constants are a=0.25, b=-5.5x10^-4. (a) What are the units of a, b? (b) Determine the value of for each of the measured temperatures -100°C, 100°C,200°C, 300'C, 400°C and plot an Et-curve.
The network of Figure below is the basic biasing arrangement for the field-effect transistor (FET), a device of increasing importance in electronic design. (Biasing simply means the application of de levels to establish a particular set of operating conditions.) Even though you may be unfamiliar with the FET, you can perform the following analysis using only the basic laws introduced in your lectures and the information provided on the diagram. a. Determine the voltages VG and Vs. b. Find the currents 11, 12, Ip, and Is. c. Determine Vps. d. Calculate VDG-
In the circuit given in the figure VT = 25mV, | VBE | = 0.7V, R1 = 712.91Kohm, R2 = 43.27Kohm, R3 = 2.29Kohm, R4 = 0.98Kohm, VCC = 10.00V, VEE = -4.00V, VA = 10.06V, Beta = 137.00, Rs = 38.43ohm, Ry Calculate the IC current according to = 16.55Kohm, Ri, R0 and the voltage gain (V0 / V1) according to the Source by full analysis When making your transactions, 2 steps will be taken after the point. Select the closest option according to +/- 10% margin of error. There is only one correct answer to the question.
The AC Bridge shown below is used to measure an unknown inductance, Lx and its internal resistance, Rx. The Bridge parameters are R1 = 20,000 ohms, R2 = 50,000 ohms, C2 = 0.003 μf, ω= 105 radians per sec. C1 is adjustable from 10 pf to 150 pf, and R3 is adjustable from 0 to 10,000 ohms. At Balance,I. Derive expressions for Rx and Lx in terms of ω, R1, R2, R3, C1, and C2.II. Determine the largest values of Rx and Lx that are measurable with the given parameters.
A DC resistive circuit includes a 5.5 mA current source, Is, which is connected to 2resistors in parallel: R1 which is 7 kΩ and R2 which has 1.75 times more conductancethan R1. There is a closed switch before R2 in series with only this resistor. Thenegative terminal of the current source is at the ground.- Firstly if you can draw the circuit diagram for the above-described circuit being sure to label allcircuit elements, current directions, and voltage polarities of each element.- The switch is now open. Redraw the circuit diagram with a voltmeter whichmeasures the voltage across the resistor R1. Be sure to label all circuit elements,current directions, and voltage polarities of each element. Indicate the valuedisplayed by the voltmeter.
Please show working out and answer for the below question. You are investigating the electrical testing circuits and find that, in an inductive circuit, the relationship between instantaneous current i (amps) and the time t (secs) is given by: i = 12.5(1-e-t/CR) Determine the time taken for current to rise from 0 to 1.9 amps with resistor value of 220 and capactor value of 0.000008
Shown below is a typical setup for a solar battery system. Sun’s energy is converted to electricity using solar PV modules. To match the output voltage of the PV module to the battery's, a charge controller is used which is a DC-DC converter. The sun’s output power is given as 1000 W/m2. The solar module has a surface area of 1 m^2 with a conversion efficiency of 10%. A charge controller converts the 20V module voltage to 12V battery voltage, with an efficiency of 84% The battery is 12V with a capacity of 10Ah. Assuming the battery is half empty (or half full, depending on your personality) and the bulb is powered on, how long will it take for the battery to be fully charged? How long can the bulb be powered at night, assuming full battery when the sun goes down and that you can fully drain the battery? (answer in hours)