PROBLEMS in EQUILIBRIUM OF PARALLEL F.S. PROBLEM SP307 A honzontal beam 10 ΚN/m supported by a roller at point A and an hinge at point B carmes parallel forces consisting of a unformly distmbuted load (UDL) and a uniformly varyıng load (UVL) as shown. Determine the reaction at the supports. 20 KN/m 6m 4m

PROBLEMS in EQUILIBRIUM OF PARALLEL F.S. PROBLEM SP307 A honzontal beam 10 ΚN/m supported by a roller at point A and an hinge at point B carmes parallel forces consisting of a unformly distmbuted load (UDL) and a uniformly varyıng load (UVL) as shown. Determine the reaction at the supports. 20 KN/m 6m 4m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.51P: The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest...

See similar textbooks

Similar questions

The uniform bar AB of weight W and length L is pinned to a sliding collar at A and to the sliding rod BD at B. The spring wound around rod BD has a stiffness k and is undeformed when rod AB is in the position =0. Determine the expression for the angle (other than =90 ) at equilibrium and investigate the stability of equilibrium for this position.
Static Problem. Indications:The system shown is composed of an ABG bar, supported by a pin at point A and by a collarsmooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and theRod BDE is supported by a pin at D and a cable at end E.Based on the above, determine:a) The load P, such that the cable force EF is T.b) The internal loads in a section passing through point G (normal and shear force, and momentflexing).c) Draw bar BDE horizontally and generate the shear force and moment diagramsflexing Indicate the maximum values of shear force and bending moment and their location.?= 22 lb ? = 7 in ? = 6 in
Referring to Prob. 10.43 and using the value found for the force exerted by the hydraulic cylinder CD , determine the change in the length of CD required to raise the 10-kN load by 15 mm.Reference to Problem 10.43:
A35-kg disk rests on an inclined surface for which µs = 0.2. The disk is connected to a beamby pin connection at A and the link is supported by pin at B. The vertical load P is applied onthe link AB at a location as shown in Figure 3 (b) Determine the support reactions at pin A and B
A spring with a torsional stiffness k is attached to the hinge at B. It is unstretched when the rod assembly is in the vertical position. Determine the weight W of the block that results in neutral equilibrium. Hint: Establish thepotential energy function for a small angle θ, i.e., approximate sin θ ≈ 0, and cos θ ≈ 1 - θ2/2.
Show how to find the force needed to move the top block. Use reasonable data and use an equilibrium analysis to explain your answer.
Method of joints: The truss pinned to the floor at D, and supported by a roller at point A is loaded as shown in Fig. T-06. Determine the force in member CG. (with explanation)
Given the Frictionless Frame as shown below with pin connection atPoint A and Point C.Determine the following if the uniform load is ‘w’:a.) The Internal Reaction at Point A in terms of w.b.) The External Reaction at Point B in terms of w.c.) The Internal Reaction at Point C in terms of w.d.) The External Reaction at Point D in terms of w. NOTE: 3 DECIMAL PLACES
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. SOLVE ASAP
The homogenous 360 kg block rests against the vertical wall, for which the coefficiewnt of friction is 0.25. A force P is applied to the midpoint of the right face in the direction shown in thre figure. What range of values may P have without disturbing equilibrium. Give solution. (Ans. 5260 N < P < 7890 N)
If the h0m0gen0us bar in equilibrium weighs 300N, what is the magnitude (N) of the tensi0n supp0rt at p0int C?
Assuming the pulley system below is weightless and frictionless pulley, determine reaction force at the ceiling when 375 N load is lifted and held in static equilibrium. Give your answer in Newtons (N) to 2 decimal places.