Processes Chemical Sdn. Bhd. is planning to minimize hot and cold utilities in their plant. The stream data is tabulated in Table 1. As a process engineer, you are required to perform pinch analysis for this plant. Table 1 Stream data Temperature Temperature Specific heat flow Streams Supply (Ts), °C Target (Tt), °C rate, kJ/s. °C Reactor 1 Feed 240 60 13 Reactor 1 Product 380 100 25 Reactor 2 Feed 40 200 18 Reactor 2 Product 120 350 28 Here is your task: 1. Identify the maximum and minimum range of ATmin for the chemical plant and justify Your answer with references

Processes Chemical Sdn. Bhd. is planning to minimize hot and cold utilities in their plant. The stream data is tabulated in Table 1. As a process engineer, you are required to perform pinch analysis for this plant. Table 1 Stream data Temperature Temperature Specific heat flow Streams Supply (Ts), °C Target (Tt), °C rate, kJ/s. °C Reactor 1 Feed 240 60 13 Reactor 1 Product 380 100 25 Reactor 2 Feed 40 200 18 Reactor 2 Product 120 350 28 Here is your task: 1. Identify the maximum and minimum range of ATmin for the chemical plant and justify Your answer with references

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.39P

See similar textbooks

Similar questions

Heat transfers Water (T= 10 C, , k=0.644 W/m.C, υ = 5.54× 10^-7 m2/s, Pr=3.55), flow over plate 1m x 1m , with velocity 2 m/s. the plate surface temperature is 90 C. Give the answer for the following: Nu number equal to Total heat transfer The flow type The average heat transfer coefficient
Briefly discuss the difference between derivative operators d and ∂. If the derivative ∂u/∂x appears in an equation, what does this imply about variable u?
We would like to develop an empirical correlation to determine the heat trans- fer coefficient, h, for turbulent flow in a circular conduit. Please use the order provided for the lists of physical variables and fundamental units in working this problem. The following physical variables are to be included: h, average fluid velocity v, density ρ, viscosity μ, thermal conductivity k, specific heat capacity c, diameter D, and length L. (a) Express each physical variable in terms of fundamental units mass (m), length (l), time (t), and temperature (θ).
THERMODYNAMICS. Question I. 0.04 kg/s of an ideal gas (molecular weight 30, ratio of specific heats 1.5) flows through a duct with a cross sectional area of 10 cm?. The pressure and temperature are 100 kPa and 350 K. What is the velocity of this gas flow, in m/s?
A cylindrical tank shown below has a radius ? and a circular orifice at the bottom of radius ?. At time ? = 0 the liquid level in the tank is ho. (a) Use the Bernoulli equation to determine the relations between the orifice velocity ?o and the free surface velocity ?s (assume the surface velocity is not zero). (b) Use conservation of mass to determine the orifice velocity in terms of the free surface velocity. (c) Use the results in (a) and (b) to derive a differential equation for h(?). Note that ?s = − dh/dt. d) Separate variables and solve the equation for h(?) with the initial condition h(0) = ho (e) Determine how long it will take to empty the tank.
For Cairo Egypt in January the average net radiation 40 W/m2, temperature is 14°C. relative humidity is 65%, and wind speed is 2.0 m/s measured @ a height of 2.0 m. Compute the evaporation rate by a) energy b) aerodynamic c) Combined d) Priestley-Taylor Method Zo=0.03
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.72 W/m deg C, Re=3840000, and Pr=0.7)?
You are being tasked as a wind tunnel engineer to investigate the performance of newly designed high-speed wind tunnel in UPNM. An exhaust gas flows through a nozzle where the inlet area is 5,000 cm2.At this inlet, the gas has a velocity of 1,200 m/s, temperature of 1,500oC,and pressure of 6,000 kPa. Initial measurement revealed that the pressure at the exit of the wind tunnel is 100 kPa. Based on this information, analyze and investigate ; i. Mach number at inlet of the nozzle ii. The velocity of gas at exit iii. The area of the nozzle at exit Take specific heat ratio for the exhaust gas, ? to be 1.7 and the gas constant, R to be 205 J/kg.
To good approximation, the thermal conductivity k of a gasdepends only on the density ρ ,mean free path l , gas constant R , and absolute temperatureT . For air at 20 8 C and 1 atm, k ≈0.026 W/(m.K) and l ≈6.5 E-8 m. Use this information to determine k for hydrogenat 20 ° C and 1 atm if l ≈ 1.2 E-7 m.
Over the ocean surface, the Bowen ratio is estimated to be about 0.2. Estimate the sensible heat and latent heat fluxes to the atmosphere, as well as the rate of evaporation, in millimeters per day, from the ocean surface, when the net radiation received just above the surface is 800W per m^2 , the heat flux to the water below 55 m is negligible, the rate of warming of the 55 m deep oceanic mixed layer is 0.12 deg. Celsius per day, and the sea surface temperature is 27deg. Celsius.
The temperature of the ball as a function of time, T(t) in thebath may be estimated by this equation:T(t) = (Ti – T∞)e–t/τ + T ∞where t is the time in seconds in the bath; Ti is the initial ball temperature;T∞ is the oil temperature; and τ is the time constant in seconds thatdepends upon the material of the ball, the geometry of the ball, and oilproperties. Assume that the initial ball temperature = 800°C, the oil temperature = 40°C, and the time constant = 50 seconds. Using MATLAB, find the time at which the temperature of the ball bearing equals 600°C, 300°C, and 50°C
Suppose we got the following data during a test of a 2- stroke engine in which gas is usedas a fuel:Diameter of the piston = 149 mmStroke length = 179 mmClearance volume = 0.88 literrpm of the engine = 302Indicated mean effective pressure = 6.0 barGas consumption = 6.0 m3/hCalorific value of the gas (fuel) = 16990 kJ/m3Make a clear sketch the geometry of this engine using the data and determine thefollowing:i. Indicated power developed by the engine in watt.ii. Air Standard Efficiencyiii. Indicated thermal efficiency of the engine.