Write a SQL Statement that give the output below.ProfitThe profit for Product ID 183 (Asus GTX780TI-3GD5) is $118.08The profit for Product ID 185 (MSI GTX 1080 TI LIGHTNING Z) is $185.63The profit for Product ID 281 (Asus ROG-POSEIDON-GTX1080TI-P11G-GAMING) is $168.84The profit for Product ID 216 (MSI GTX 1080 TI LIGHTNING X) is $121.84The profit for Product ID 6 (Zotac ZT-P10810A-10P) is $147.64The profit for Product ID 108 (MSI GAMING) is $96.81The profit for Product ID 83 (Asus STRIX-GTX1080TI-O11G-GAMING) is $138.86The profit for Product ID 215 (PNY VCOP4000-PB) is $105.89

Here SQL statement based on assumptions about the database schema and data is:

Profit The profit for Product ID 183 (Asus GTX780TI-3GD5) is $118.08 The profit for Product ID 185 (MSI GTX 1080 TI LIGHTNING Z) is $185.63 The profit for Product ID 281 (Asus ROG-POSEIDON-GTX1080TI-P11G-GAMING) is The profit for Product ID 216 (MSI GTX 1080 TI LIGHTNING X) is $121.84 The profit for Product ID 6 (Zotac ZT-P18810A-10P) is $147.64 The profit for Product ID 108 (MSI GAMING) is $96.81

Profit The profit for Product ID 183 (Asus GTX780TI-3GD5) is $118.08 The profit for Product ID 185 (MSI GTX 1080 TI LIGHTNING Z) is $185.63 The profit for Product ID 281 (Asus ROG-POSEIDON-GTX1080TI-P11G-GAMING) is The profit for Product ID 216 (MSI GTX 1080 TI LIGHTNING X) is $121.84 The profit for Product ID 6 (Zotac ZT-P18810A-10P) is $147.64 The profit for Product ID 108 (MSI GAMING) is $96.81

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

You have an AVR ATmega16 microcontroller, one yellow LED, and one bicolor LED. Write aprogram to make the bicolor LED start out green for 3 seconds (connected at I/O pin PB0). After 3seconds, change the bicolor LED to red (connected at I/O pin PB1). When the bicolor LED changesto green, flash the yellow LED (connected at I/O pin PB2) on and off once every second for tenseconds. When the yellow LED is done flashing, the bicolor LED should switch back to red andstay that way.
I could use some help with making a working code for a 12 hour clock system in verilog for my DE0lite or any other Fpga Board. I am being unable to get the results correct
22 zay? Jump to level 1 Given the input/output combination for the barrel shifter, select the values of w, x, y, and z. 0000 0000 0110 1101 Pick v sh <<8 in -0 Pick sh <<4 in0 y Pick sh <<2 in-0 Pick sh <<1 in 0 1010 0000 0000 0000
Create an IPO (Input-Process-Output) of the prototype "An Arduino Mega 2560 Earthquake Detection System for Real-Time Magnitude Calculation and Aftershock Analysis using ADXL345 Accelerometer". Note: The IPO must be in the table format
Develop a program by using Assimbly Language for PIC16F877a, to turn on a LED is connected to PORTA,2 by a switch is attached to PORTB 2 The LED should turn on when the switch is on, and turn off when the switch is off
How do I write a c++ code on microchip studio to control an ADC 0808 with an atmega328p to light up 8 leds connected to the ADC with a potentiometer and all hardware connections as depicted in the diagram?
digital design
Which of the following best describes how to construct a 1 to 8 demultiplexer from a 3 to 8 decoder: * Connect the decoder enable input to D Connect the ith decoder output to Di O Connect all the decoder input select lines CBA to D Connect all the decoder input data lines to Di Connect Y to D and W to D'
IC 8255 has O a. 40 pins b. 32 pins C. 24 pins d. 8 pins O d.
How to use C language to set up the following question. for MPLAB homework Steps Connect the following components to the PIC24HJ device on your breadboard: 1. 2 LEDs: a) LED 0 to RB13 (is IC pin) b) LED 1 to RB14 (is IC pin) 2. 1 Push Button: a) PB to RB11 (is IC pin) 3. Write a state machine in C language to perform the following LED sequence. a) Both LED 0 and LED 1 are turned on, i.e. 11 b) Press the PB to start the repeating LED sequence with one second between patterns: 10, 01, 11,00 (1 LED is on , 0 LED IS off) c) Release the button to stop LED at 00. Press the PB will go to (b).
An XY flip-flop operates as follows. If XY = 00, next state of flip-flop is 1 If XY = 01, next state of flip-flop is the complement for present state If XY = 10, next state of flip-flop is the same as present state If XY = 11, next state of flip-flop is 0 (Table 1) Present State Next State Qn Y Qn+1 1 1 1 A client has approached you to design a controller for a simple elevator in his warehouse, which has two floors. The elevator can be at any one of the two floors: Ground or First and is controlled by one button that has two values: Up (1) or Down (0). There are two lights in the elevator that indicate the current floor: Red for Ground, and Green for First. At each clock cycle, the controller will check the current input and current floor and will change the Ilights and floors as required by the user. Develop the state diagram and design the controller using the XY flip- flop!
C.| Chegg.com The 74LS47 I.C. shown in the attached diagram is a: 2022 The circuit shown has a '1' on the data select line, 0110' on A3,A2,A1,A0 and 1001' on B3,B2,B1,B0. Data select EN BCD7-seg GI A T MUX A, B, A, 74LSI57 74LS47 88 Common-cathode displays B digit (MSD) A digit (LSD) Decoder A1 ation IY, b B1 GI (EN) 74LS139 O Multiplexer O Demultiplexer O Comparator O Encoder O Decoder