Q-2 A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig .If a moment of 680 N.m is applied at B. Determine the maximum stress in each section of the shaft. what will be the angle of twist of each portion 680 N.m 50 mm 25 mm ,8m

Q-2 A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig .If a moment of 680 N.m is applied at B. Determine the maximum stress in each section of the shaft. what will be the angle of twist of each portion 680 N.m 50 mm 25 mm ,8m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.2P: A solid circular bar having diameter d is to be replaced by a rectangular tube having...

See similar textbooks

Related questions

Q: 4. The solid shaft and tube shown in Figure are made of a material having an allowable shear stress…

Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…

Q: Solve Problem for the maximum shear stress within regions AC and BC, and the angle of twist f of end…

A: Considering Section AC, Maximum Shear Stress: Considering Section BC, Maximum Shear Stress:

Q: A 1.625-in.-diameter solid steel shaft supports loads PA = 340 lb, Pc = 540 lb, and PE = 340 lb, as…

Q: 3. A solid shaft is shown below. If d = 100 mm, 1 = 1 m, Me = 2n kN m, and the allowable shear…

Q: 3.8 Attaching a hollow shaft to a solid shaft creates the steel shaft. Determine the maximum torque…

Q: 3.34 The steel shaft with two different diameters rotates at 4 Hz. The power sup- plied to gear C is…

Q: 5. The equilateral triangular tórsión member has sides equai lU D thickness t (Figure a). Figure b…

A: TMAX=100mpaG=70×103 mpab=16cmt=1cmTJ=ζr=GθLwhere θ and L consider as 1

Q: 3.22 The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques…

Q: Q.1: Calculate the maximum shear stress developed in each segment when the torque T = 100 N.m. is…

Q: A 1.750-in.-diameter solid steel shaft supports loads PA = 280 lb, Pc = 510 lb, and PE = 280 lb, as…

Q: A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig.If a moment of 680 N.m…

A: GivenLength of circular bar L=3mmoment apllied at point B M=680Nmlength of AB L1=1.8mdia ofAB…

Q: 3.6 Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB…

A: Diameter of the steel shaft AB, D= 15 mm Maximum allowable shear force in the shaft, τ= 120 MPa…

Q: The constant wall thickness of a steel tube with the cross section shown is 2 mm. If a 600-N m…

A: Given data: d=10 mmri=9 mmt=2 mmro=11 mmT=600 N.mG=80 GPa Need to determine the shear stress in the…

Q: 3.6 Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB…

Q: A simply supported beam supports the loads shown in the figure. The cross-sectional dimensions of…

Q: Q2/Find diameter of BR,ST, and AL if maximum shear stress for St=Al=12.73 Mpa and for Br=0.707. then…

A: As per given question we have to determine the angle of twist at free end

Q: A solid 1.375 in. diameter shaft is subjected to a torque of T = 340 lb ft and an axial load Pacting…

Q: A 12 mm The steel shaft is made from two segments: AC has a diameter of 12 mm, and CB has a 125 mm D…

A: According to the information we have a steel shaft with two segments AC and CB torque on the shaft…

Q: A cylindrical metal tube of mean radius r = 5 in., length L = 14 ft, and shear modulus G = 11 x 106…

Q: A steel plate of dimensions 2.5 × 1.2 × 0.1 m is hoisted by a cable sling that has a clevis at each…

Q: 2 kip/ft 6 in 10 in B. +40 kip 16 in D. 16 in 5t 5 ft 10 ft The simply-supported beam-column above…

Q: 2. A composite shaft is subjected to two torques as shown below. Shaft AB is a solid aluminum (G =…

A: Given, Section AB:GAB = 25 GPa = 25000 N/mm2LAB = 400 mmTAB = 800 Nm = 800,000 NmmdAB = 36 mmJAB =…

Q: A solid bar having a diameter 150 mm is to be replaced by a square tube having a cross-sectional…

Q: Q-2 A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig .If a moment of 680…

Q: A compound steel [G = 80 GPa] shaft consists of a solid 92-mm-diameter segment (1) and a solid…

Q: The stepped shaft shown in the figure is supported by bearings at A and B. Determine the maximum…

Q: The hollow shaft shown in the figure below is fixed at one end and has a lever at the other. The…

Q: 340 lb ft and an axial load Pacting as shown in the figure. If the A solid 1.375 in. diameter shaft…

Q: 60 N- m Since each of the shafts 144 N - m , AB, BC and CD shown in the figure consists of a solid…

A: The torsional moment applied on the shaft AB is, TAB=48 N·m The diameter of the shaft AB is, dAB=15…

Q: 324. A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown…

Q: d steel shaft 25kw at 300rpm.It carries the size of the shaft,if the allowable shear stress is 46MPa…

A: Given:P=25 KWN=300 rpmζmax=46 MPaσmax=57 MPa

Q: 3.8 The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum…

Q: A shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in…

Q: A 1.875-in-diameter solid steel shaft supports loads PA = 360 lb, Pc = 520 lb, and PE = 360 Ib, as…

Q: 3.6 Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB…

A: Find the largest allowable value of P.

Q: 1. The shaft assembly shown below is fixed at its ends A and D. It consists of an aluminum (G= 30…

Q: A 28mm diameter steel shaft AB is built into a rigid wall at A and supported by a smooth bearing at…

Q: Rigid beam AB rests on the two short posts shown in Fig. 4–7a. AC is made of steel and has a…

A: Solution:

Q: n 66 mm diameter alloy shaft is 6.5 m long and subjected to twisting. The shaft is attached to a…

A: Given: The overall length, L = 6.5 m The shear modulus, G = 81 GPa Teh diameter of shaft, d = 66 mm…

Q: A 18-mm-diameter solid steel shaft supports loads PA = 1,400 N and Pc = 2,100 N as shown. Assume L₁…

Q: Q3 Two shaft is attached to a rigid wall at each end. For the bronze segment AB. the diameter is 75…

Q: A 1.00-in.-diameter solid steel shaft supports loads Pa = 485 lb and PD = 279 lb as shown. Assume L1…

Q: A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid…

Q: A rod has a circular cross section with a diameter of 2 in. It is subjected to a torque of 12 kip #…

A: Given:Diameter of rod,D=2 inTorque acting on rod,T=12 kip in

Q: A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig.If a moment of 680 N.m…

A: For the material of the shaft G= 80 GN/m2. Twisting moment/Total torque= 680 N m L1= 1.8 m L2= 1.2 m…

Q: From the figure shown below, determine the stress of member AB and BC. And calculate the maximum…

A: Stress: Stress is defined as the ratio of the Resistance force of the body when an external load is…

Q: The solid steel shaft shown below has a diameter of 20 mm and fixed to rigid wall at A and B. If it…

Q: A 1.125-in-diameter solid steel shaft supports loads PA = 270 Ib, Pc = 550 lb, and PE = 270 Ib, as…

Q: 30 kN ww Β 4 m 2 m Formüller: F.L F F σ-Ε.ε, ε-, ΔL- α.LΔT, ΔL Α.Ε. Α A

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Q-2 A circular bar ABC 3m long is rigidly fixed at its ends A and C shown in fig .If a moment
of 680 N.m is applied at B. Determine the maximum stress in each section of the shaft. what
will be the angle of twist of each portion
680 N.m
B
50 mm
25 mm
+- 1,2m
1,8m
U ル

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.