Q-2 A single-threaded power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to "raise" and "lower" the load.

Q-2 A single-threaded power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to "raise" and "lower" the load.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single-threaded 25-mm power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45 mm. Find the overall efficiency, and the torque to “raise” and “lower” the load. If the effort load is 75 N, find the force ratio and movement ratio.
A 600 mm steel pulley transmits 50 kW at 900 rpm. The arc of contact between the belt and pulley is 144 degrees, the coefficient of friction between belt and pulley is 0.3 and the safe working stress of the belt is 2750 kPa. Find the width of the belt used if the thickness is equal to 12 mm.
A double square thread power screw has a mean radius of 90 mm and pitch of 12 mm is used to lift a load of 90 kN. If the friction of screw Is 0.14 and collar torque Is 25% of input torque, find the input torque required.
(6) A double square-threaded power screw transmits 1,800in-lb of torque and raises a machine head; the head is guided by linear slides with anti-friction bearings, and thus no appreciable friction is involved. If the coefficient of friction for the threads is 0.1, find: (a) the load that can be raised if the screw has 2 threads/in and an outside diameter of 2½in; (b) if a 4000-lb load is to be lowered, what torque must the screw transmit? (c) if the power screw of rotates 10 rpm, what is the linear speed of the driven head in feet per minute?
A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces has worn away by 1.25 mm. find the maximum power that can be transmitted assuming uniform wear. A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces…
Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?
A 15KW and 1200r.p.m motor drives a compressor at 300r.p.m through a pair of spur gears having 20° stub teeth .the centre to centre distance between the shafts is 400mm.the motor pinion is made to forged steel having an allowable static stress 210MPa while the gear is made of cast steel having an allowable static stress as 140MPa.Assuming that the drive operates 8 to 10 hours per day under light shock conditions,find from the standpoint of strength (a) Module;(b)face width and (c)number of teeth an pitch circle diameter of each gear.check the gears thus designed from the consideration of wear .the surface endurance limit may be taken as 700MPa.
The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum pressure under working conditions is 220kPa only. The clutch is used to connect two 25mm solid shafts with allowable shearing stress of 69 MPa. The inner and outer diameter of the clutch face is 60 mm and 120mm, respectively. What is the power in kW transmitted at 1000 rpm?
A double square threaded power screw has an efficiency of 65% when raising a load. Friction angle for threads is 8.54o, with collar friction negligible. The pitch diameter of the screw is 70 mm. When lowering a load, a uniform speed is maintained by a brake. If the load is 10 tons, what torque must be exerted by the brake? Is this screw self-locking?
A single trapezoidal metric thread power screw is to raise a load of 60 kN. The screw has a mean diameter of 34 mm and a pitch of 5 mm. The coefficient of thread friction and collar friction are 0.15 and 0.11, respectively. The collar mean diameter is 90 mm and the screw turns at 150 rpm. Determine the total torque required to raise the load in N-m.
(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?
Write legibly, provide manual step by step solution, and diagram for below given problem. A 2 in diameter 6-spline shaft ( d= 0.85D, W= 0.25D, h= 0.075D ) and to slide when not under load has a compressive force of 2500 lbs. Find the torque applied if hub length is 2 1/2 in Ans. 2312.5 in-lb