Q-2: For a simply supported beam shown in figure below and by using Ultimate Strength Design Method, find the area of steel for the following data:- W 20KN/m, WD-18KN/m (including self-weight), f-400MPA, f-30MPa, b-250mm, d-400mm, dt-422mm, if there is need for compression steel use d'-50mm. Wp 18KN/m WLA20KN/m Brick Wall 8m

Q-2: For a simply supported beam shown in figure below and by using Ultimate Strength Design Method, find the area of steel for the following data:- W 20KN/m, WD-18KN/m (including self-weight), f-400MPA, f-30MPa, b-250mm, d-400mm, dt-422mm, if there is need for compression steel use d'-50mm. Wp 18KN/m WLA20KN/m Brick Wall 8m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Topic : Uncracked and cracked section 1. A beam has a width of 300mm and effective depth of 540mm, d’ = 60mm. It is reinforced with 4 – 25mm diam tension bars and 2 – 25mm compression bars. f'c = 28mpa and fy= 420. What is the ultimate moment capacity of the beam?
M1AQ99. For a loaded propped beam in the figure below, design a singly reinforced beam (using the USD method and NSCP 2015) for the positive moment. Give the complete details of the design. The total depth of the beam must not exceed 600 mm to ensure acceptable floor-to-floor vertical clearance. f'c = 28 MPa and fy = 415.7 MPa. It carries a super- imposed dead load of 90 kN/m and a live load of 38.4 kN/m all applied over the entire length of the beam. Other load and beam properties are the following: L1 = 6.3 m, L2 = 2.1 m, I2 = 0.65 of I1. Use a minimum concrete cover of 60 mm. Optimize the design such that the minimum percent difference of the moment strength with the actual moment is 1% but to avoid overdesign it's max percent difference is 5%. Design the rectangular beam details to provide: width, total depth, effective depth, number and diameter of tension bars (for two layers, provide number of bars in the upper and lower layer and vertical clear spacing between the 2 layers),…
Design a 355mm wide rectangular short tied column with bars only in two end faces for Pu = 2224 kN, Mu = 339 kN m, f'c = 27.6 MPa (4ksi) and fy = 413.7 MPa (60ksi), and effective cover of 25mm. Select a column size (provide the dimension "h") with approximately 2% steel. Use interaction diagrams shown below.. (See Figure 1 for column section) 355 mm X Figure 1 k к h
A UC 305x305x118 steel column supports a single beam framing into its web and connected using a fin plate Steel column web beam.JPG GkA = 159 kN QkA= 193 kN What is the design eccentric bending moment Mz,Ed applied to the weak axis of the column? Give your answer to the nearest kNm and do not include the units in the answer box.
Problem 1. A W30 x 116 beams has the top flange restrained against lateral displacement and rotation and has an unstiffened web. A point load is applied to the top flange at 2m. From the left support. The beam spans 12 m. Use A36 steel with yield strength of Fy = 248 Mpa. b. Compute the maximum value of point load that may be applied without web crippling occurring. d = 762 mm; K = 41.28 mm; bf = 266.7 mm; tf = 21.59 mm; tw = 14.33 mm
Calculate area of tensile steel for a singly R.C. beam 230 mm x 380 mm size and factored moment 50 kN.m. Use concrete M-20 and steel Fe-500 grade, effective cover 35 mm. (i) Use design aid method. (ii) Use analytical method. (iii) Using equation of p
A W 5300*101 of Steel Section (fy= 345 MPa & fu= 450 MPa) is used as simply supported beamwith a span of 15 The dead load is the summation of the super dead load (X1=9 kN/m as uniform load) and the beam weight. In addition to the dead load, a uniform live load is applied to the beam. If the lateral support is provided at 3-meter intervals, what is the maximum service live load in kN/m that can be supported.
A W8x35 steel column has unsupported length of 8m. Using A36 steel, compute for the ultimate axial load capacity (in kN) if both ends are a.) PINNED b.) FIXED? Neglect local buckling. W8x35 Properties A = 6645.15mm^2 lx = 52.45 x 10^6 mm^4 ly = 17.69 x 10^6 rx = 88.9 mm ry = 51.56mm
Q: For the beam shown in Figure (1) below, which is carrying a service live load (P= ? kN) and dead load of self weight. fc'=28 MPa, fy=400MP, d=425mm. Using the ultimate method, find the live load (P). area of steel at te * 2350 mm 3053mm 1540 mm 1600mm 2210mm 1390mm
Compute the design moment strength of the beam section described below if fy = 420 MPa, fc’ = 21 MPa. d = 650 mm d’ = 70 mm b = 450 mm As’: 3-28mm dia. As: 4-36mm dia
Q) Determine the elastic and plastic moment of resistance of the RC beam. The beam is a trapezoid in shape. B1 at top = 300mm, B2 at bottom = 500mm, total height = 600mm, height from top to the bottom of the steel reinforcement = 570mm, As = 1473mm^2, Fy=350MPa, Fcu=30MPa Solve this early I upvote
for the given beam, find the required area of steel both in compression and tension to ensure the beam is in tension region.Live load moment = 200 kN.m. and deadload moment = 245kN.m. Use fc = 28 mpa, fy= 415 Mpa, steel cover = 65 mm